Comandos de route map redistribucion (como se hace)
- 1. Comandos de Route map: Si quisiera que la red 100.40.40.0/24 del R1 vaya por arriba
200.40.40.0/24 del R9
Pasos:
1. R2(config)# access-list 110 permit ip 100.40.40.0 0.0.0.255 200.40.40.0 0.0.0.255
2. R2(config)#route-map arriba permit
3. R2(config-route-map)#match ip address 110
4. R2(config-route-map)#set ip next-hop 50.40.40.2
5. R2(config)#interface serial 1/0
6. R2(config-if)#ip policy route-map arriba
Resultado: Se va por arriba
Tracing the route to 210.40.40.10
1 10.40.40.2 64 msec 28 msec 20 msec
2 50.40.40.2 80 msec 16 msec 68 msec
3 60.40.40.2 76 msec 48 msec 68 msec
4 70.40.40.2 96 msec 76 msec 96 msec
5 80.40.40.2 96 msec 88 msec 102 msec
REDISTRIBUCION
RIP
Router(config)#router rip
.Redistribuir rutas de OSPF:
Router(config-router)#redistribute ospf [ID] metric 2 (2)
.Redistribuir rutas de EIGRP:
Router(config-router)#redistribute eigrp [AS] metric 2 (2)
- 2. EIGRP
Router(config)#router EIGRP [AS]
.Redistrubuir rutas de RIP:
Router(config-router)#redistribute rip metric 10000 10 255 1 1500
.Redistribuir rutas de OSPF:
Router(config-router)#redistribute ospf [ID] metric 10000 100 255 1 1500 (
1)
OSPF
Router(config)#router OSPF [ID]
.Redistrubuir rutas de EIGRP:
Router(config-router)#redistribute eigrp [AS] subnets
.Redistribuir rutas de RIP:
Router(config-router)#redistribute rip subnets
Redistribución: (RIP-OSPF)
Configuraciones de los extremos:
R1(config)#router rip
R1(config-router)#version 2
R1(config-router)#network 192.168.10.0
R1(config-router)#network 10.1.1.0
R7(config)#router ospf 20
R7(config-router)#network 20.1.1.0 0.0.0.255 area 0
R7(config-router)#network 192.168.20.0 0.0.0.255 area 0
Ahora el medio (LO MAS IMPORTANTE) para que vea los 2 protocolos
R2(config)#router ospf 20
- 3. R2(config-router)#redistribute rip subnets
R2(config-router)#network 20.1.1.0 0.0.0.255 area 0
R2(config)#router rip
R2(config-router)#version 2
R2(config-router)#redistribute ospf 20 metric 15
R2(config-router)#network 10.1.1.0
R2(config-router)#no auto-summary
Redistribución: (OSPF-EIGRP)
Configuraciones de los extremos:
R8(config)#router ospf 10
R8(config-router)#network 192.168.10.0 0.0.0.255 area 0
R8(config-router)#network 10.1.1.0 0.0.0.255 area 0
R4(config)#router eigrp 20
R4(config-router)#network 20.1.1.0 0.0.0.255
R4(config-router)#network 192.168.20.0 0.0.0.255
Ahora el medio (LO MAS IMPORTANTE) para que vea los 2 protocolos
R3(config)#router ospf 10
R3(config-router)#redistribute eigrp 20 subnets metric-type 1
R3(config-router)#network 10.1.1.0 0.0.0.255 area 0
R3(config)#router eigrp 20
R3(config-router)#redistribute ospf 10 metric 10000 100 255 1 500
R3(config-router)#network 20.1.1.0 0.0.0.255