This ppt explains develop Optimum Energy Management System that can be controlled remotely using a landline connection. It is one of the most emerging trends in modernization of home appliance control.
Edgefxkits.com has a wide range of electronic projects ideas that are primarily helpful for ECE, EEE and EIE students and the ideas can be applied for real life purposes as well.
http://www.edgefxkits.com/
Visit our page to get more ideas on popular electronic projects developed by professionals.
Edgefx provides free verified electronic projects kits around the world with abstracts, circuit diagrams, and free electronic software. We provide guidance manual for Do It Yourself Kits (DIY) with the modules at best price along with free shipping.
2. http://www.edgefxkits.com/
Optimum Energy Management System
Abstract:
๏ This application keeps the database of the number of persons entering
as well as exiting.
๏ 555 timer driven 38 KHz signal from IR LED gets interrupted on to the
IR receiver to sense the person entering as well as exiting which is fed
to a 555 timer.
๏ The output of 555 timer is fed to the Microcontroller for analyzing and
control purpose
3. http://www.edgefxkits.com/
Optimum Energy Management System
Introduction:
๏ The project is designed to monitor the number of persons entering as
well as exiting a room. Electrical loads are switched ON as the first
person enters and switches OFF when the last person leaves. IR sensors
used in combination with microcontroller to monitor all the operations.
This helps in saving lot of energy.
7. http://www.edgefxkits.com/
555 TIMER
The 555 Has Three Operating Modes:
Monostable mode:
๏ In this mode, the 555 functions as a "one-shot". Applications include
timers, missing pulse detection, switches, touch switches, frequency
divider, capacitance measurement, pulse-width modulation (PWM) etc.
Optimum Energy Management System
8. http://www.edgefxkits.com/
Optimum Energy Management System
Astable:
๏ The 555 can operate as an oscillator. Uses include LED and lamp
flashers, pulse generation, logic clocks, tone generation, security
alarms, pulse position modulation, etc.
Bistable mode or Schmitt trigger:
๏ The 555 can operate as a flip-flop, if the DIS pin is not connected and
no capacitor is used. Uses include bounce free latched switches, etc.
9. http://www.edgefxkits.com/
Optimum Energy Management System
Micro Controller:
๏ 8K Bytes of In-System Programmable (ISP) Flash Memory
๏ 4.0V to 5.5V Operating Range
๏Crystal Frequency 11.0592MHZ
๏ Three-level Program Memory Lock
๏ 256 x 8-bit Internal RAM
๏ 32 Programmable I/O Lines
๏ Three 16-bit Timer/Counters
AT89S52
11. http://www.edgefxkits.com/
Optimum Energy Management System
IR LED:
๏ An IR LED, also known as IR transmitter, is a special
purpose LED that transmits infrared rays in the range of
760 nm wavelength.
๏ Such LEDs are usually made of gallium arsenide or
aluminum gallium arsenide. They, along with IR
receivers, are commonly used as sensors.
๏ The appearance is same as a common LED. Since the
human eye cannot see the infrared radiations, it is not
possible for a person to identify whether the IR LED is
working or not, unlike a common LED.
12. http://www.edgefxkits.com/
Optimum Energy Management System
BC547:
๏ The BC547 transistor is an NPN Epitaxial Silicon Transistor.
๏ The BC547 transistor is a general-purpose transistor in small
plastic packages.
๏ It is used in general-purpose switching and amplification
BC847/BC547 series 45 V, 100 mA NPN general-purpose
transistors.
๏ Whenever base is high, then current starts flowing through
base and emitter and after that only current will pass from
collector to emitter
14. http://www.edgefxkits.com/
Optimum Energy Management System
Circuit Diagram Explanation:
๏ There are two pair sensors, each kept at certain distance from the other.
One pair of sensor consists of a transmitter and a receiver, kept exactly
opposite to each other. The transmitting part emits modulated IR light
which is received at the receiver end and fed to a microcontroller of
8051 family.
๏ When a person enters the room then microcontroller senses it (with the
help of IR sensors) and increments the count and displays it on 7
segment displays and also switches ON the load. In the same way
when a person exits the room, the count gets decremented. When the
last person exits from the room, the lamp is switched OFF. The load
operation is handled by a relay interfaced to the microcontroller.
15. http://www.edgefxkits.com/
Optimum Energy Management System
Advantages:
๏ Managing and reducing energy consumption not only saves money but
also helps in mitigating climate change and enhancing corporate
reputation.
๏ Energy management is widely acknowledged as the best solution for
direct and immediate reduction of energy consumption.
16. http://www.edgefxkits.com/
Optimum Energy Management System
Conclusion:
๏ Optimum Energy Management System is designed to monitor the number
of persons entering as well as exiting a room. Electrical loads are switched
ON as the first person enters and switches OFF when the last person
leaves. IR sensors used in combination with microcontroller to monitor all
the operations. This helps in saving lot of energy.