3. Doka column formwork Framax Xlife
from Framax Xlife universal panels
with Universal panels 90 with Universal panels 120
H= 0.90 / 1.35 / 2.70 / 3.30 m
e.g.
25 x 25 cm
max.
105 x 105 cm
e.g.
60 x 20 cm
max.
75 x 75 cm
3 Column formwork
6. Doka column formwork KS
very short erection and striking times, thanks to
simple unfold / refold construction
entire formwork repositioned in one piece, in one
single crane lift
one system for any cross-section
from 20 – 60 cm
Triangular ledges for chamfering the corners
Panel heights
0.90 m / 1.20 m / 2.70 m / 3.30 m columns can be
formed up to a height of 3.30 m with no joins
6 Column formwork
7. KS Xlife sheeting
Threaded fasteners are in the rear face – no marks left on the concrete!
7 Column formwork
12. Column formwork
with Frami Xlife universal panels
Frami Xlife formwork pressure:80 kN/m²
H= 1.20 / 1.50 / 2.70 / 3.00 m
Universal panel 0.90m
e.g. 20 x 60 cm column
max. column 65 x 65 cm
Universal panel 0.75m
The Universal panel 0.90m
lets you form column cross-
sections of up to 80 x 80 cm
12 Column formwork
14. Doka Column formwork RS
for high demands on surface
150 kN/m2
fresh concrete pressure
diameter from 30 to 60 cm (custom sizes on
request)
panel heights
0.25 m / 0.50 m / 1.00 m / 3.00 m
Short forming-time
integrated connectors
quick connector for Panel struts
centring function
14 Column formwork
20. Ladder system XS
safe vertical access routes with integral ladder
cages, to meet the most stringent safety rules
can be pre-assembled at ground level
can also be retro-attached
low transport volume
for Column formwork platform 150/90cm
20 Column formwork
21. XS-connector
column
formwork
Ladder cage
XS 1.00 m
Ladder cage
exit XS
XS-connector
FX / Alu-FX
XS-connector
KS
XS-connector
RS
Ladder cage XS shown
stacked for transportSituation during assembly
Situation
during lifting
XS-connector
wall formwork
2.30 m 4.40 m
Overview of system components
21 Column formwork
EUROPARK II
Europark Salzburg, Column formwork RS with Framax Xlife
Features of columns
many different shapes
high load-bearing capacity
great precision
Due to the wide variety of different shapes,
almost impossible to fit into a grid by either
size or
height
High pouring rates cause high loads
Many columns are fair-faced concrete objects
TIM_68409,
The Doka column-formwork solutions
Framax prop from standard framed formwork
Doka column formwork Alu with special panel type for maximum versatility
Wooden formwork beams and steel waling : column formwork made up of four GF panels
Framax Xlife 90 cm: column dimensions max. 75 x 75 cm
Alu-Framax Xlife 75 cm: max. 60 x 60 cm
accessories, Universal fixing bolt, Super-plate 15.0
grid for every 5 cm
high loads of up to 90 kN/m²
Vertical stacking with
75/90 panels or
Universal panels 75/90 aluminium
Universal panels 90/135 steel
Maximum column cross-sections: 60x60 cm
High-speed column formwork:
Possible in 5 cm increments with the Universal framed formwork panel
With drop-in, ready-to-use pouring platform
Allow for the necessary number of panel struts (we recommend 3 panel struts per half-side)
Doka column formwork KS
Vöcklabruck Hospital (Austria)(00/0802-1)
the panels are simply unfolded/refolded by hand, so the formwork can be erected and struck with no need for a crane
+ entire formwork is lifted by crane in one piece = time-savings
Panel heights up to 3.30 m, for clean, join-free concrete surfaces
Fair-faced concrete completely free of markings because the sheeting is secured from the back.
TIM_58966, COLUMN FORMWORK KS
Shifting wheel KS
The Shifting wheel is an add-on which brings advantages like:
easier stripping-out and forming-up
craneless horizontal transport of entire formwork units, as column-forms of up to 3.6 m in height can be wheeled to their next location(take account of circumstances which may affect shifting!)
Frami Xlife as a column formwork
Column formwork Frami with Universal panels
5 cm grid
Doka Column formwork RS
ready-made Column formwork in Doka System for circular or oval cross-sections
diameter in 5 cm grid
height grid 50 cm
precisely fitting panel joints, centring function
Panel strut
Can be connected directly to
Framax/Alu-Framax
Circular formwork H20
Europark II, Salzburg,
TIM_64201, EUROPARK II
Steel walings and corner connection plates
Structured from 4 elements
* Sheathing
* Timber formwork beams
* Steel walings
* Beam fixtures
Interlinking of elements
* Corner connecting plate (opposite) gives 1 L-section
* Universal angle-tie bracket diagonally braced for rapid closing and opening
Steel waling WS 10
up to 70 / 70 cm
Steel waling WS 12
up to 120 / 120 cm
See “Calculation Guide”
Doka column formwork
Detail corner:
displaced formwork sheeting joint for exactness, tightness
Mounting parts for extraordinary geometries:
e.g. circular, ellipse
column dimension by mounting parts without modification:
e.g. craneway console
HLAG Asten
(high-speed railway line)
Complicated shapes, tailor-made from large-area formwork
More suitable for large columns
With all the advantages of large-area formwork
Regulations necessitating Ladder system XS in Austria & Germany:
On formwork above 5 m in height, ladder cages are compulsory from 3 m upwards
TIM_62351, COLUMN FORMWORK
Note: The Ladder cage exit XS does not fold down, but is stored in the upright.
The special feature of the Doka solution is the fact that the column formwork can be pre-assembled entirely at ground level, complete with all its safety devices – meaning that safety is ensured right from the word "go". The ladder is swivel-mounted on the XS connector, so that when the formwork is hoisted by the crane, the ladder rotates into the vertical. Where necessary, the pouring platform – complete with ladder and ladder cage – can be retrofitted to existing column formworks.