3. Structure of a hydraulic
system
This simplified block
diagram shows the
division of hydraulic
systems into a signal
control section and a
hydraulic power
section. This signal
control section is used
to activate the valves in
the power control
section.
4. Hydraulic power section
The diagram of the hydraulic power
section is complemented in this
case by a circuit diagram to allow
correlation of the various function
groups; the power supply section
contains the hydraulic pump and
drive motor and the components for
the preparation of the hydraulic
fluid. The energy control section
consists of the various valves used to
provide control and regulate the
flow rate, pressure and direction of
the hydraulic fluid. This drive
section consists of cylinders or
hydraulic motors, depending on the
application in question.
6. Interaction of components
The animations show the
sequences in a basic
hydraulic circuit in
simplified form - the
actuation and spring
return of the final control
element (4/2-way valve),
the advance and return of
the drive component
(double acting cylinder)
and the opening and
closing of the pressure
relief valve.
15. Circuit diagram: Return flow filter
An oil filter situated in the
return line to the tank has
the advantage that the
filter is thus easy to
maintain. A
disadvantage, however, is
that contamination is
removed from the
hydraulic fluid only after it
has passed through the
hydraulic components.
This configuration is often
used.
16. Circuit diagram : Pump inlet filter
With this
configuration, the pump is
protected from
contamination. The filter
is, on the other hand, less
easily accessible.
If these filters have a too
fine mesh, suction
problems and cavitation
effects may occur.
Additional coarse filters
upstream of the pump are
recommended.
17. Circuit diagram: Pressure line
filter
Pressure filters can be
installed selectively
upstream of valves which
are sensitive to
contamination; this also
enables smaller mesh sizes
to be used.
A pressure-resistant
housing is required, which
makes this configuration
more expensive.
18. Circuit diagram: Contamination
indicator
It is important that the effectiveness
of a filter can be checked by a
contamination indicator. The
contamination of a filter is
measured by the pressure drop; as
the contamination increases, the
pressure upstream of the filter
increases. The pressure acts on a
spring- loaded piston. As the
pressure increases, the piston is
pushed against a spring.
There are a number of different
display methods. Either the piston
movement is directly visible or it is
converted into an electrical or visual
indication by electrical contacts.
19. Circuit diagram: Hydraulic power
unit
The illustration shows
the detailed circuit
symbol for a hydraulic
power unit.
Since this is an
combination unit, a
dot/dash line is placed
around the symbols
representing the
individual units.
20. Pressure relief valve (1)
In this design
incorporating a poppet
valve, a seal is pressed
against the inlet port P by a
pressure spring when the
valve is in its normal
position.
In this situation, for
example, an unloaded
piston rod is executing an
advance stroke and the
entire pump delivery is
flowing to the cylinder.
21. Circuit diagram: Pressure relief
valve (2)
As soon as the force
exerted by the inlet
pressure at A exceeds the
opposing spring force, the
valve begins to open.
In this situation, for
example, the piston rod is
fully advanced; the entire
pump delivery is flowing at
the preset system pressure
to the tank.
22. PRV used to limit system pressure
This illustration shows a
pressure relief valve within
a basic hydraulic circuit
(used to control a double
acting cylinder).
The resistances at the
outlet (tank line, filter)
must be added to the force
of the spring in the
pressure relief valve. See
also the animation
“Interaction of
components” (at page 7).
23. PRV used to limit system pressure
This illustration shows
the same circuit as the
previous
illustration, but with
the cut-away view of
the PRV replaced by
the appropriate circuit
symbol.
24. (1A) Circuit without brake valve
(Animation)
One application of pressure
relief valves is as brake valves;
these prevent pressure peaks
which may otherwise occur as
the result of mass moments of
inertia when a directional
control valve is suddenly closed.
The animation shows an
(incorrect) circuit in schematic
form in which the working line
on the exhaust side has
fractured due to the absence of a
brake valve.
The next animation shows the
correct circuit.
29. (2) Circuit diagram: Brake valve
This illustration shows the
correct circuit for the problem in
topic 1A. This circuit
incorporates not only a brake
valve on the piston-rod side but
also a non-return valve on the
inlet side via which oil can be
taken in from a reservoir during
the vacuum phase following the
closure of the directional control
valve.
The following animation shows
the events which occur in the
two working lines.
30. Circuit with brake valve
(Animation)
The animation (2a) shows
in schematic form the
behavior of the PRV during
the braking phase, while
(2b) shows the behavior of
the non-return valve
(NRV) in the supply line
and (2) shows the two
events together in
summary.
The necessity of the brake
valve can be demonstrated
by the preceding
animation.
