SlideShare a Scribd company logo
1 of 38
Download to read offline
ELECTRIC DRIVE
SELECTION OF MOTOR FOR
DIFFERENT TYPES OF LOADS OR
SERVICE
BY
Prof. Sagar B. Kudkelwar
Electrical Engineering Department
Ballarpur Institute of Technology,
Ballarpur.
Rolling Mills
 Metal rolling is one of the most important manufacturing processes in the
modern world.
 Metal rolling is often the first step in creating raw metal forms.
The ingot or continuous casting is hot rolled into a bloom or a slab,
 There are two types of two types mills
1.Blooming Mill
2. Slabing Mill
 these are the basic structures for the creation of a wide range of
manufactured forms.
 Blooms typically have a square cross section of greater than 6x6 inches.
 Slabs are rectangular and are usually greater than 10 inches in width and
more than 1.5 inches in thickness
 .Rolling is most often, (particularly in the case of the conversion of an ingot
or continuous casting), performed hot.
 rolling operation requires production of heavy torque at low r.p.m. to effect
heavy reduction of material from ingots to blooms or slabs.
 Blooming mill may have 2 rolls or 3 rolls.
 two high blooming mill has arrangement of reversing the direction of
rotation of the rolls in order to carry out rolling of material through
successively reducing passes.
 In case of three high mill direction of rotation need not to be changed.
 By the use of tilt tables material can be pass between lower and middle
rolls or between middle and top rolls.
Blooms and slabs as obtained from blooming mill are further subjected to
rolling to produce plates, structural bars or billets.
Billets when further rolled produce rounds, square octagons ,flats angles etc.
Electric drive
Two Rolling Mill Three Rolling Mill
Depending upon type of mill selection of motor has to satisfy
following conditions.
1) Motor should have robust construction to withstand severest duty
2) It should be capable of developing short time torque to the extent
of 2 or 3 times of rated torque.
3) It should be capable of having wide speed variation.
4) It should be in a position to maintain preselected speed within
tolerances from no load to full load. Therefore it should have
quick response to change.
Various motors used for Rolling Mills
 Induction Motors:
• we can change the speed of slip induction motor by introducing
resistance in the rotor circuit.
• This method is wasteful as the reduction in speed is proportional to
copper losses taking place in rotor circuit.
• As such slip motors are used for small re-rolling mills where wide
speed range is not required.
• besides wastage of energy taking place in rotor, introduction of
resistance in rotor circuit converts the speed torque characteristic of
induction motor from shunt to series.
• Therefore speed can not e maintained constant from no load to full load.
• This will therefore motor to fly off to no load as soon as stock passes out
of the stand.
• this much reflects very much rolling on the quality stands of the rolling
mill.
•As such slip ring motors are suitable for roughing stands of the rolling mill.
•Wastage of energy in the rotor of slip motor which is proportional to the
reduction of speed can be avoided by employing cascaded induction motor
D. C. Motor
• D.C. motor is the only type of motor which can satisfy the stringent
requirements of modern rolling mills.
• By varying the applied voltage to the armature and keeping field constant
it is possible to change the speed of motor at constant torque up to rated
speed.
• In this way requirement of higher constant torque at low speed needed for
effecting heavy reduction in first passes is achieved.
• on the other hand low torque and higher speed is required for rolling
operation in final passes when for the section of stock having become
smaller, torque needed is low and elongated material requires higher speed
to clear off in the shortest possible time.
• this achieved by weakening field. after rated speed is achieved by the
increase of applied voltage to the armature.
• so in this way we get high speed at reduced torque i.e. H.P. remains same.
• In case of reversible rolling mills, in order to ensure high rate of
acceleration ,it becomes necessary to reduce the moment of inertia of motor
to minimum .
• this is achieved by increasing the length and diameter of armature.
• D.C. moors of rolling mills can be supplied from three phase a. c.
system by any of the following methods:
1) Grid controlled mercury arc rectifier
2) Silicon controlled rectifier
3) ward Leonard set
• The main advantage of grid controlled rectifier are its overload capacity,
steeples control of voltage from 0-100%, high efficiency and quick
response to very rapid changes in operating variables.
• the only disadvantage of mercury arc rectifier is that load peaks cause
by the operating of the mill are transferred to the feeding system.
• Due to this reason mercury arc rectifier or silicon controlled rectifier
which works only as valve is recommended for supplying the rolling mill
where a. c. supply net work is sufficient strong.
• the main advantage of silicon rectifier is its small size.
• the main advantage of employing ward Leonard set is that load peaks is
not transferred o the supply.
SYNCHRONOUS MOTOR
• Synchronous motors are used for driving continuous mill where load is
maintained for relatively long period.
• Flywheel can not be used and consequently the motor carries can the entire
load.
• for slow speed, synchronous motors can be built more economically than
induction motors and at the same time, get P.F. correction.
• Besides main mill drive , motors are required for auxiliary drive such as for
driving the rolls of roller table, adjusting the gap between rolls, driving the
manipulators, for chopping the tail ends, cutting the material to required
length, winding the ends product into coils etc.
CRANES
Essential Requirement of a hoist or crane motor
o It should develop high starting torque
o It should withstand great number of switching operations.
D.C. MOTORS
 D.C. is usually employed on cranes in steel mills where safety and flexibility of
control are of first importance.
 Series motor is by far the most commonly type of motor which is used on account of
its inherent characteristic such that it adjust its speed to load.
 This characteristics prevents excessive power demand on heavy loads.
 During Dynamic breaking, series motor works as shunt generator..
A.C. Motors
• on cranes using a. c. slip ring induction motor are used where speed
control is obtained by rotor resistance.
• Speed range of slip ring motor is less than that of series motor .
• Dynamic breaking is applied by giving unbalanced supply to primary.
• This is done by giving single phase supply to the primary such that two
phase windings are in parallel and this in turns is in series with thir
winding.
• for outdoor service totally enclosed motors are best.
•Hoist motors have special electro-mechanical breaks which are applied
by springs to hold the load as soon as supply to motor goes off.
Electric drive
PAPER MILL
• Pulp stuff from storage tank after passing through strainers comes to
first section of paper making machine which consists of moving wire
mesh.
• subsequently this sheet of paper goes in between series of heated press
rolls, drying rolls, calendars, smoothing rolls and finally to reelers.
Following requirements for paper mill drive must be fulfilled :
1) To manufacture different types of paper we should be
able to vary the speed of entire series of rolls.
2) Relative speeds of rolls should be constant otherwise
tearing of paper may result.
1) We should be able to adjust the speed of any group of
rolls relative to others in order to allow for the draw
of the paper.
All above requirements are fulfilled by the use of
Schrage motor
Paper Mill Process
Marine Drive
• Electric Drive propeller of ship is universal
Propeller: A propeller is type of fan that transmits power by conversion rotational
motion into thrust. A pressure difference is produced between the forward and
rear surfaces of the airfoil-shaped blade, and a fluid (such as air or water) is
accelerated behind the blade.
It has following Advantages.
1) Steam turbine or diesel engine has most economical speed of about 3000 r.p.m.
and 400 to 800 r.p.m. respectively. Propeller speed on the other had is in
between 100 to 200. r.p.m. We can run propeller and prime mover
independently. This enables prime mover to run at its most economical speed
2) At the time of slow speeds we can run only few prime mover sets to supply all
the propellers. Low speed cruising is now no longer uneconomical.
3) position of prime mover Speed control and reversing in case of electric
propulsion are easy and can be carried out from any convenient position instead
of signaling to engine room
• Position is not fixed by the propeller shaft as such there is greater
flexibility in the layout.
• In Case of very big ships, electric drive will be by three phase induction or
synchronous motors
• prime mover will be steam turbine, driving three phase alternator.
• Speed control is done by variation of applied voltage and partly by
frequency variation.
• Reversal is obtained by changing the phase sequence of the supply.
• Speed of induction motor can also be change by pole changing method
which give economical speed.
•Disadvantage of induction motor is that it’s P.F. at low speed is low
between 0.7 to 0.75.
• Power at the ship is generated by turbo alternator at 2.2 to 6.6 kv
• Small ships can be driven by D.C. motors, which are controlled by means
of ward Leonard method.
• Power on the ships is generated by diesel electric set, relatively at low
voltage of 650 V
TEXTILE MILLS
• Loom motors operate in atmosphere which is laden wool-lint and moisture.
• Further the motor should high starting torque of about 2to3 times full load
torque.
• Loom motors have to start and stop many times in a day.
• this increases the motor heating during starting.
• Motors of low temperature rise under full load conditions are therefore
selected do that under working conditions of frequent starting and stopping
permissible temperature rise is not exceeded
• Keeping above requirements in view totally enclosed, fan cooled, high
torque squirrel cage motors are selected
• Where only wool lint is present and no moist atmosphere ,screen protected
motors are used.
• Splash proof motors are used in wet locations such as dye house.
• Brush shaft adjustable speed motor is used on printing machine
MINES
Motor used inside mines should have flame proof
enclosure.
For mine winders, it is essential to have both speed
control as well as breaking capacity
Ward Leonard system is most effective drive.
Slip Induction motor with D.C. dynamic breaking is also
used.
We may also used D.C. motor supplied from controlled
rectifier.
PUNCHES PRESSES & SHEARS
• Since heavy sudden loads are applied , D.C.
compound motor or slip ring motor with
flywheel is used.
LATHE, GRINDING & MILLING
MACHINE
• These machine tools require low starting torque and constant
operating speed.
• Therefore D.C. shunt motors or squirrel cage motors are
needed.
• In case of drills, requiring different operating speeds for
different metals.
• motors having two sets of stator pole changing winding are
used which give economical speed.
Lathe Machine
Grinding Machine
• Drip proof or totally enclosed surface cooled motors are most
frequently used, often mounted on a common bed plate and direct
coupled to the pump.
• Sometimes motor is flange mounted.
• Where pump speed does not come within the range of the fixed
motor speed ,V belt drive is employed.
• starting torque necessary for centrifugal pumps is about 40 to
50% of full load torque.
PUMPS
• For reciprocating pumps starting torque may be 100 to 200
% of full load torque
• It is advisable to use slip ring motors for reciprocating
pumps and squirrel cage motors for centrifugal pumps
Centrifugal Pump
Electric drive
REFRIGERATION & AIR CONDITIONING
• In vapor compression system of refrigeration motor is used to drive the
compressor.
• This motor is controlled by thermostat .
• When motor is restarted , it has to drive compressor against high speed
pressure.
• Motor should therefore be required developing starting torque of 200 to
250% full load torque.
• For small unit air conditioners, capacitor type single phase 230 V motor
with D.O.L. starter is most commonly selected.
• High torque squirrel cage induction motor or slip ring induction motors are
used for large installations
• For very large plant size, synchronous motor, driving
turbo compressor may be found suitable specially when P.F.
correction is also required.
Compressor
Electric drive
LIFTS
• High smooth accelerating torque of 200 to 250% full load
torque at starting, high over load capacity and pull out torque
an maximum degree of silence are essential requirements.
• Motor are normally one hour rated for duty cycle of 150 to
180 starts per hour.
• D.C. compound motors or slip ring motors suit the above
requirements
BELT CONVEYERS
• Belt conveyors are used for moving sand, coal
and others raw materials.
• Heavy loads have to accelerated.
• High torque squirrel cage or preferably slip ring
motors should be made as per requirement.
• Due to outside working conditions and presence
of grit and dust in atmosphere ,totally enclosed
surface cooled motors are used.
Electric drive
DOMESTIC USE
• Universal series motor is used for house hold
appliances such as Mixer, Washing Machine,
Sewing Machine, Vacuum Cleaner
Mixer
Washing Machine
Washing Machine Motor
Sewing Machine
Vacuum Cleaner

More Related Content

What's hot

Speed control of 3 phase induction motor
Speed control of 3 phase induction motorSpeed control of 3 phase induction motor
Speed control of 3 phase induction motormpsrekha83
 
Introduction to Electric Drives
Introduction to Electric DrivesIntroduction to Electric Drives
Introduction to Electric Drivesrrsurani
 
Presentation on starter
Presentation on starterPresentation on starter
Presentation on starteraftab alam
 
Speed Control of Synchronous Motor
Speed Control of Synchronous Motor Speed Control of Synchronous Motor
Speed Control of Synchronous Motor Ashutosh Jha
 
Permanent magnet brushless dc motors ppt
Permanent magnet brushless dc motors pptPermanent magnet brushless dc motors ppt
Permanent magnet brushless dc motors pptsrmrithi
 
Synchronous reluctance motor
Synchronous reluctance motorSynchronous reluctance motor
Synchronous reluctance motorkarthi1017
 
Power Electronic Converter
Power Electronic ConverterPower Electronic Converter
Power Electronic ConverterAli
 
Starting method for 3 phase induction motor
Starting method for 3 phase induction motorStarting method for 3 phase induction motor
Starting method for 3 phase induction motorAhmed A.Hassan
 
Repulsion motor
Repulsion motorRepulsion motor
Repulsion motorMuhsin ali
 
Presentation on induction motor
Presentation on induction motorPresentation on induction motor
Presentation on induction motorWaqar Muhammad
 
Electric Drives and Controls Unit 1 Introduction
Electric Drives and Controls Unit 1 IntroductionElectric Drives and Controls Unit 1 Introduction
Electric Drives and Controls Unit 1 IntroductionDr.Raja R
 
Electrical drives and_controls
Electrical drives and_controlsElectrical drives and_controls
Electrical drives and_controlsddsshukla
 
Slip power recovery schemes EDC
Slip power recovery schemes EDC Slip power recovery schemes EDC
Slip power recovery schemes EDC STALLONRAJ
 
Induction motor three phase
Induction motor three phase Induction motor three phase
Induction motor three phase Study
 
Breaking,Types of Electrical Braking system, Regenerative Braking, Plugging ...
Breaking,Types of Electrical Braking system, Regenerative Braking,  Plugging ...Breaking,Types of Electrical Braking system, Regenerative Braking,  Plugging ...
Breaking,Types of Electrical Braking system, Regenerative Braking, Plugging ...Waqas Afzal
 

What's hot (20)

Speed control of 3 phase induction motor
Speed control of 3 phase induction motorSpeed control of 3 phase induction motor
Speed control of 3 phase induction motor
 
Introduction to Electric Drives
Introduction to Electric DrivesIntroduction to Electric Drives
Introduction to Electric Drives
 
Presentation on starter
Presentation on starterPresentation on starter
Presentation on starter
 
Brushless dc motor
Brushless dc motorBrushless dc motor
Brushless dc motor
 
Synchronous machines
Synchronous machinesSynchronous machines
Synchronous machines
 
Speed Control of Synchronous Motor
Speed Control of Synchronous Motor Speed Control of Synchronous Motor
Speed Control of Synchronous Motor
 
Permanent magnet brushless dc motors ppt
Permanent magnet brushless dc motors pptPermanent magnet brushless dc motors ppt
Permanent magnet brushless dc motors ppt
 
Brushless DC Motors
Brushless DC MotorsBrushless DC Motors
Brushless DC Motors
 
Synchronous reluctance motor
Synchronous reluctance motorSynchronous reluctance motor
Synchronous reluctance motor
 
Power Electronic Converter
Power Electronic ConverterPower Electronic Converter
Power Electronic Converter
 
Soft starters
Soft startersSoft starters
Soft starters
 
Starting method for 3 phase induction motor
Starting method for 3 phase induction motorStarting method for 3 phase induction motor
Starting method for 3 phase induction motor
 
Repulsion motor
Repulsion motorRepulsion motor
Repulsion motor
 
Presentation on induction motor
Presentation on induction motorPresentation on induction motor
Presentation on induction motor
 
Induction motor
Induction motorInduction motor
Induction motor
 
Electric Drives and Controls Unit 1 Introduction
Electric Drives and Controls Unit 1 IntroductionElectric Drives and Controls Unit 1 Introduction
Electric Drives and Controls Unit 1 Introduction
 
Electrical drives and_controls
Electrical drives and_controlsElectrical drives and_controls
Electrical drives and_controls
 
Slip power recovery schemes EDC
Slip power recovery schemes EDC Slip power recovery schemes EDC
Slip power recovery schemes EDC
 
Induction motor three phase
Induction motor three phase Induction motor three phase
Induction motor three phase
 
Breaking,Types of Electrical Braking system, Regenerative Braking, Plugging ...
Breaking,Types of Electrical Braking system, Regenerative Braking,  Plugging ...Breaking,Types of Electrical Braking system, Regenerative Braking,  Plugging ...
Breaking,Types of Electrical Braking system, Regenerative Braking, Plugging ...
 

Similar to Electric drive

Unit 3 EHV - I.pptx
Unit 3 EHV - I.pptxUnit 3 EHV - I.pptx
Unit 3 EHV - I.pptxPavanP76
 
Presentation2
Presentation2Presentation2
Presentation2mittal434
 
UEE UNIT-1(2022).ppt
UEE UNIT-1(2022).pptUEE UNIT-1(2022).ppt
UEE UNIT-1(2022).pptVishwanani1
 
written pole electric motor
written pole electric motorwritten pole electric motor
written pole electric motorsuresh_ash
 
Ac motors and their types
Ac motors and their typesAc motors and their types
Ac motors and their typesYasar Hayat
 
Single phase induction motor
Single phase induction motorSingle phase induction motor
Single phase induction motorGowtham Packiaraj
 
THREE PHASE INDUCTION MOTOR
THREE PHASE INDUCTION MOTORTHREE PHASE INDUCTION MOTOR
THREE PHASE INDUCTION MOTORmasum heera
 
TOPIC 4.1- A.C. Motors.pptx
TOPIC 4.1- A.C. Motors.pptxTOPIC 4.1- A.C. Motors.pptx
TOPIC 4.1- A.C. Motors.pptxMartMantilla1
 
TRACTION MOTORS in Electric Traction.ppt
TRACTION MOTORS in Electric Traction.pptTRACTION MOTORS in Electric Traction.ppt
TRACTION MOTORS in Electric Traction.pptDrAyyarKandasamy
 
Wind Turbine Gearbox
Wind Turbine GearboxWind Turbine Gearbox
Wind Turbine GearboxAmanHindocha1
 
Presentation induction motors 2
Presentation induction motors 2Presentation induction motors 2
Presentation induction motors 2Edmund Lor
 
Pneumatic rotary actuators
Pneumatic rotary actuatorsPneumatic rotary actuators
Pneumatic rotary actuatorsAkshay Bedwal
 
Type of Single phase induction Motor
Type of Single phase induction MotorType of Single phase induction Motor
Type of Single phase induction MotorSmit Shah
 
AC Motors,Types & Applications.pptx
AC Motors,Types & Applications.pptxAC Motors,Types & Applications.pptx
AC Motors,Types & Applications.pptxHASNAINNAZIR1
 
SELECTION OF DRIVES AND CONTROL SCHEMES FOR MACHINE TOOLS
SELECTION OF DRIVES AND CONTROL SCHEMES FOR MACHINE TOOLS SELECTION OF DRIVES AND CONTROL SCHEMES FOR MACHINE TOOLS
SELECTION OF DRIVES AND CONTROL SCHEMES FOR MACHINE TOOLS Praveen Kumar
 
Power electronic converter in wind turbine
Power electronic converter in wind turbinePower electronic converter in wind turbine
Power electronic converter in wind turbineSonuKumarBairwa
 
Introduction to motors
Introduction to motorsIntroduction to motors
Introduction to motorsavocado1111
 
PRINCIPLES OF AC MOTORS AND THEIR TYPESS
PRINCIPLES OF AC MOTORS AND THEIR TYPESSPRINCIPLES OF AC MOTORS AND THEIR TYPESS
PRINCIPLES OF AC MOTORS AND THEIR TYPESSEzhilarasan Ganesan
 

Similar to Electric drive (20)

Unit 3 EHV - I.pptx
Unit 3 EHV - I.pptxUnit 3 EHV - I.pptx
Unit 3 EHV - I.pptx
 
Presentation2
Presentation2Presentation2
Presentation2
 
UEE UNIT-1(2022).ppt
UEE UNIT-1(2022).pptUEE UNIT-1(2022).ppt
UEE UNIT-1(2022).ppt
 
written pole electric motor
written pole electric motorwritten pole electric motor
written pole electric motor
 
Ac motors and their types
Ac motors and their typesAc motors and their types
Ac motors and their types
 
Single phase induction motor
Single phase induction motorSingle phase induction motor
Single phase induction motor
 
THREE PHASE INDUCTION MOTOR
THREE PHASE INDUCTION MOTORTHREE PHASE INDUCTION MOTOR
THREE PHASE INDUCTION MOTOR
 
TOPIC 4.1- A.C. Motors.pptx
TOPIC 4.1- A.C. Motors.pptxTOPIC 4.1- A.C. Motors.pptx
TOPIC 4.1- A.C. Motors.pptx
 
TRACTION MOTORS in Electric Traction.ppt
TRACTION MOTORS in Electric Traction.pptTRACTION MOTORS in Electric Traction.ppt
TRACTION MOTORS in Electric Traction.ppt
 
Wind Turbine Gearbox
Wind Turbine GearboxWind Turbine Gearbox
Wind Turbine Gearbox
 
Presentation induction motors 2
Presentation induction motors 2Presentation induction motors 2
Presentation induction motors 2
 
Pneumatic rotary actuators
Pneumatic rotary actuatorsPneumatic rotary actuators
Pneumatic rotary actuators
 
Type of Single phase induction Motor
Type of Single phase induction MotorType of Single phase induction Motor
Type of Single phase induction Motor
 
AC Motors,Types & Applications.pptx
AC Motors,Types & Applications.pptxAC Motors,Types & Applications.pptx
AC Motors,Types & Applications.pptx
 
Report on jaypee rewa abhinav
Report on jaypee rewa abhinavReport on jaypee rewa abhinav
Report on jaypee rewa abhinav
 
SELECTION OF DRIVES AND CONTROL SCHEMES FOR MACHINE TOOLS
SELECTION OF DRIVES AND CONTROL SCHEMES FOR MACHINE TOOLS SELECTION OF DRIVES AND CONTROL SCHEMES FOR MACHINE TOOLS
SELECTION OF DRIVES AND CONTROL SCHEMES FOR MACHINE TOOLS
 
Power electronic converter in wind turbine
Power electronic converter in wind turbinePower electronic converter in wind turbine
Power electronic converter in wind turbine
 
Introduction to motors
Introduction to motorsIntroduction to motors
Introduction to motors
 
single phaser IM.pptx
single phaser IM.pptxsingle phaser IM.pptx
single phaser IM.pptx
 
PRINCIPLES OF AC MOTORS AND THEIR TYPESS
PRINCIPLES OF AC MOTORS AND THEIR TYPESSPRINCIPLES OF AC MOTORS AND THEIR TYPESS
PRINCIPLES OF AC MOTORS AND THEIR TYPESS
 

Recently uploaded

Engineering Mechanics Chapter 5 Equilibrium of a Rigid Body
Engineering Mechanics  Chapter 5  Equilibrium of a Rigid BodyEngineering Mechanics  Chapter 5  Equilibrium of a Rigid Body
Engineering Mechanics Chapter 5 Equilibrium of a Rigid BodyAhmadHajasad2
 
Test of Significance of Large Samples for Mean = µ.pptx
Test of Significance of Large Samples for Mean = µ.pptxTest of Significance of Large Samples for Mean = µ.pptx
Test of Significance of Large Samples for Mean = µ.pptxHome
 
Lifting Plan | Lifting Plan for Different Process Equipment | Gaurav Singh Ra...
Lifting Plan | Lifting Plan for Different Process Equipment | Gaurav Singh Ra...Lifting Plan | Lifting Plan for Different Process Equipment | Gaurav Singh Ra...
Lifting Plan | Lifting Plan for Different Process Equipment | Gaurav Singh Ra...Gaurav Singh Rajput
 
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdfSummer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdfNaveenVerma126
 
IT3401-WEB ESSENTIALS PRESENTATIONS.pptx
IT3401-WEB ESSENTIALS PRESENTATIONS.pptxIT3401-WEB ESSENTIALS PRESENTATIONS.pptx
IT3401-WEB ESSENTIALS PRESENTATIONS.pptxSAJITHABANUS
 
How to Write a Good Scientific Paper.pdf
How to Write a Good Scientific Paper.pdfHow to Write a Good Scientific Paper.pdf
How to Write a Good Scientific Paper.pdfRedhwan Qasem Shaddad
 
Renewable Energy & Entrepreneurship Workshop_21Feb2024.pdf
Renewable Energy & Entrepreneurship Workshop_21Feb2024.pdfRenewable Energy & Entrepreneurship Workshop_21Feb2024.pdf
Renewable Energy & Entrepreneurship Workshop_21Feb2024.pdfodunowoeminence2019
 
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...Amil baba
 
Graphics Primitives and CG Display Devices
Graphics Primitives and CG Display DevicesGraphics Primitives and CG Display Devices
Graphics Primitives and CG Display DevicesDIPIKA83
 
EPE3163_Hydro power stations_Unit2_Lect2.pptx
EPE3163_Hydro power stations_Unit2_Lect2.pptxEPE3163_Hydro power stations_Unit2_Lect2.pptx
EPE3163_Hydro power stations_Unit2_Lect2.pptxJoseeMusabyimana
 
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...Amil baba
 
Modelling Guide for Timber Structures - FPInnovations
Modelling Guide for Timber Structures - FPInnovationsModelling Guide for Timber Structures - FPInnovations
Modelling Guide for Timber Structures - FPInnovationsYusuf Yıldız
 
A Seminar on Electric Vehicle Software Simulation
A Seminar on Electric Vehicle Software SimulationA Seminar on Electric Vehicle Software Simulation
A Seminar on Electric Vehicle Software SimulationMohsinKhanA
 
OS Services, System call, Virtual Machine
OS Services, System call, Virtual MachineOS Services, System call, Virtual Machine
OS Services, System call, Virtual MachineDivya S
 
Pioneering Process Safety Management: The Future Outlook
Pioneering Process Safety Management: The Future OutlookPioneering Process Safety Management: The Future Outlook
Pioneering Process Safety Management: The Future Outlooksoginsider
 
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docxSUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docxNaveenVerma126
 
Phase noise transfer functions.pptx
Phase noise transfer      functions.pptxPhase noise transfer      functions.pptx
Phase noise transfer functions.pptxSaiGouthamSunkara
 

Recently uploaded (20)

Engineering Mechanics Chapter 5 Equilibrium of a Rigid Body
Engineering Mechanics  Chapter 5  Equilibrium of a Rigid BodyEngineering Mechanics  Chapter 5  Equilibrium of a Rigid Body
Engineering Mechanics Chapter 5 Equilibrium of a Rigid Body
 
Test of Significance of Large Samples for Mean = µ.pptx
Test of Significance of Large Samples for Mean = µ.pptxTest of Significance of Large Samples for Mean = µ.pptx
Test of Significance of Large Samples for Mean = µ.pptx
 
Lifting Plan | Lifting Plan for Different Process Equipment | Gaurav Singh Ra...
Lifting Plan | Lifting Plan for Different Process Equipment | Gaurav Singh Ra...Lifting Plan | Lifting Plan for Different Process Equipment | Gaurav Singh Ra...
Lifting Plan | Lifting Plan for Different Process Equipment | Gaurav Singh Ra...
 
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdfSummer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
Summer training report on BUILDING CONSTRUCTION for DIPLOMA Students.pdf
 
IT3401-WEB ESSENTIALS PRESENTATIONS.pptx
IT3401-WEB ESSENTIALS PRESENTATIONS.pptxIT3401-WEB ESSENTIALS PRESENTATIONS.pptx
IT3401-WEB ESSENTIALS PRESENTATIONS.pptx
 
How to Write a Good Scientific Paper.pdf
How to Write a Good Scientific Paper.pdfHow to Write a Good Scientific Paper.pdf
How to Write a Good Scientific Paper.pdf
 
Renewable Energy & Entrepreneurship Workshop_21Feb2024.pdf
Renewable Energy & Entrepreneurship Workshop_21Feb2024.pdfRenewable Energy & Entrepreneurship Workshop_21Feb2024.pdf
Renewable Energy & Entrepreneurship Workshop_21Feb2024.pdf
 
Lecture 2 .pdf
Lecture 2                           .pdfLecture 2                           .pdf
Lecture 2 .pdf
 
Présentation IIRB 2024 Chloe Dufrane.pdf
Présentation IIRB 2024 Chloe Dufrane.pdfPrésentation IIRB 2024 Chloe Dufrane.pdf
Présentation IIRB 2024 Chloe Dufrane.pdf
 
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
Popular-NO1 Kala Jadu Expert Specialist In Germany Kala Jadu Expert Specialis...
 
Graphics Primitives and CG Display Devices
Graphics Primitives and CG Display DevicesGraphics Primitives and CG Display Devices
Graphics Primitives and CG Display Devices
 
EPE3163_Hydro power stations_Unit2_Lect2.pptx
EPE3163_Hydro power stations_Unit2_Lect2.pptxEPE3163_Hydro power stations_Unit2_Lect2.pptx
EPE3163_Hydro power stations_Unit2_Lect2.pptx
 
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
Best-NO1 Best Rohani Amil In Lahore Kala Ilam In Lahore Kala Jadu Amil In Lah...
 
Présentation IIRB 2024 Marine Cordonnier.pdf
Présentation IIRB 2024 Marine Cordonnier.pdfPrésentation IIRB 2024 Marine Cordonnier.pdf
Présentation IIRB 2024 Marine Cordonnier.pdf
 
Modelling Guide for Timber Structures - FPInnovations
Modelling Guide for Timber Structures - FPInnovationsModelling Guide for Timber Structures - FPInnovations
Modelling Guide for Timber Structures - FPInnovations
 
A Seminar on Electric Vehicle Software Simulation
A Seminar on Electric Vehicle Software SimulationA Seminar on Electric Vehicle Software Simulation
A Seminar on Electric Vehicle Software Simulation
 
OS Services, System call, Virtual Machine
OS Services, System call, Virtual MachineOS Services, System call, Virtual Machine
OS Services, System call, Virtual Machine
 
Pioneering Process Safety Management: The Future Outlook
Pioneering Process Safety Management: The Future OutlookPioneering Process Safety Management: The Future Outlook
Pioneering Process Safety Management: The Future Outlook
 
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docxSUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
SUMMER TRAINING REPORT ON BUILDING CONSTRUCTION.docx
 
Phase noise transfer functions.pptx
Phase noise transfer      functions.pptxPhase noise transfer      functions.pptx
Phase noise transfer functions.pptx
 

Electric drive

  • 1. ELECTRIC DRIVE SELECTION OF MOTOR FOR DIFFERENT TYPES OF LOADS OR SERVICE BY Prof. Sagar B. Kudkelwar Electrical Engineering Department Ballarpur Institute of Technology, Ballarpur.
  • 2. Rolling Mills  Metal rolling is one of the most important manufacturing processes in the modern world.  Metal rolling is often the first step in creating raw metal forms. The ingot or continuous casting is hot rolled into a bloom or a slab,  There are two types of two types mills 1.Blooming Mill 2. Slabing Mill  these are the basic structures for the creation of a wide range of manufactured forms.  Blooms typically have a square cross section of greater than 6x6 inches.  Slabs are rectangular and are usually greater than 10 inches in width and more than 1.5 inches in thickness  .Rolling is most often, (particularly in the case of the conversion of an ingot or continuous casting), performed hot.
  • 3.  rolling operation requires production of heavy torque at low r.p.m. to effect heavy reduction of material from ingots to blooms or slabs.  Blooming mill may have 2 rolls or 3 rolls.  two high blooming mill has arrangement of reversing the direction of rotation of the rolls in order to carry out rolling of material through successively reducing passes.  In case of three high mill direction of rotation need not to be changed.  By the use of tilt tables material can be pass between lower and middle rolls or between middle and top rolls. Blooms and slabs as obtained from blooming mill are further subjected to rolling to produce plates, structural bars or billets. Billets when further rolled produce rounds, square octagons ,flats angles etc.
  • 5. Two Rolling Mill Three Rolling Mill
  • 6. Depending upon type of mill selection of motor has to satisfy following conditions. 1) Motor should have robust construction to withstand severest duty 2) It should be capable of developing short time torque to the extent of 2 or 3 times of rated torque. 3) It should be capable of having wide speed variation. 4) It should be in a position to maintain preselected speed within tolerances from no load to full load. Therefore it should have quick response to change.
  • 7. Various motors used for Rolling Mills  Induction Motors: • we can change the speed of slip induction motor by introducing resistance in the rotor circuit. • This method is wasteful as the reduction in speed is proportional to copper losses taking place in rotor circuit. • As such slip motors are used for small re-rolling mills where wide speed range is not required. • besides wastage of energy taking place in rotor, introduction of resistance in rotor circuit converts the speed torque characteristic of induction motor from shunt to series.
  • 8. • Therefore speed can not e maintained constant from no load to full load. • This will therefore motor to fly off to no load as soon as stock passes out of the stand. • this much reflects very much rolling on the quality stands of the rolling mill. •As such slip ring motors are suitable for roughing stands of the rolling mill. •Wastage of energy in the rotor of slip motor which is proportional to the reduction of speed can be avoided by employing cascaded induction motor
  • 9. D. C. Motor • D.C. motor is the only type of motor which can satisfy the stringent requirements of modern rolling mills. • By varying the applied voltage to the armature and keeping field constant it is possible to change the speed of motor at constant torque up to rated speed. • In this way requirement of higher constant torque at low speed needed for effecting heavy reduction in first passes is achieved. • on the other hand low torque and higher speed is required for rolling operation in final passes when for the section of stock having become smaller, torque needed is low and elongated material requires higher speed to clear off in the shortest possible time. • this achieved by weakening field. after rated speed is achieved by the increase of applied voltage to the armature. • so in this way we get high speed at reduced torque i.e. H.P. remains same. • In case of reversible rolling mills, in order to ensure high rate of acceleration ,it becomes necessary to reduce the moment of inertia of motor to minimum . • this is achieved by increasing the length and diameter of armature.
  • 10. • D.C. moors of rolling mills can be supplied from three phase a. c. system by any of the following methods: 1) Grid controlled mercury arc rectifier 2) Silicon controlled rectifier 3) ward Leonard set • The main advantage of grid controlled rectifier are its overload capacity, steeples control of voltage from 0-100%, high efficiency and quick response to very rapid changes in operating variables. • the only disadvantage of mercury arc rectifier is that load peaks cause by the operating of the mill are transferred to the feeding system. • Due to this reason mercury arc rectifier or silicon controlled rectifier which works only as valve is recommended for supplying the rolling mill where a. c. supply net work is sufficient strong. • the main advantage of silicon rectifier is its small size. • the main advantage of employing ward Leonard set is that load peaks is not transferred o the supply.
  • 11. SYNCHRONOUS MOTOR • Synchronous motors are used for driving continuous mill where load is maintained for relatively long period. • Flywheel can not be used and consequently the motor carries can the entire load. • for slow speed, synchronous motors can be built more economically than induction motors and at the same time, get P.F. correction. • Besides main mill drive , motors are required for auxiliary drive such as for driving the rolls of roller table, adjusting the gap between rolls, driving the manipulators, for chopping the tail ends, cutting the material to required length, winding the ends product into coils etc.
  • 12. CRANES Essential Requirement of a hoist or crane motor o It should develop high starting torque o It should withstand great number of switching operations. D.C. MOTORS  D.C. is usually employed on cranes in steel mills where safety and flexibility of control are of first importance.  Series motor is by far the most commonly type of motor which is used on account of its inherent characteristic such that it adjust its speed to load.  This characteristics prevents excessive power demand on heavy loads.  During Dynamic breaking, series motor works as shunt generator..
  • 13. A.C. Motors • on cranes using a. c. slip ring induction motor are used where speed control is obtained by rotor resistance. • Speed range of slip ring motor is less than that of series motor . • Dynamic breaking is applied by giving unbalanced supply to primary. • This is done by giving single phase supply to the primary such that two phase windings are in parallel and this in turns is in series with thir winding. • for outdoor service totally enclosed motors are best. •Hoist motors have special electro-mechanical breaks which are applied by springs to hold the load as soon as supply to motor goes off.
  • 15. PAPER MILL • Pulp stuff from storage tank after passing through strainers comes to first section of paper making machine which consists of moving wire mesh. • subsequently this sheet of paper goes in between series of heated press rolls, drying rolls, calendars, smoothing rolls and finally to reelers.
  • 16. Following requirements for paper mill drive must be fulfilled : 1) To manufacture different types of paper we should be able to vary the speed of entire series of rolls. 2) Relative speeds of rolls should be constant otherwise tearing of paper may result. 1) We should be able to adjust the speed of any group of rolls relative to others in order to allow for the draw of the paper. All above requirements are fulfilled by the use of Schrage motor
  • 18. Marine Drive • Electric Drive propeller of ship is universal Propeller: A propeller is type of fan that transmits power by conversion rotational motion into thrust. A pressure difference is produced between the forward and rear surfaces of the airfoil-shaped blade, and a fluid (such as air or water) is accelerated behind the blade. It has following Advantages. 1) Steam turbine or diesel engine has most economical speed of about 3000 r.p.m. and 400 to 800 r.p.m. respectively. Propeller speed on the other had is in between 100 to 200. r.p.m. We can run propeller and prime mover independently. This enables prime mover to run at its most economical speed 2) At the time of slow speeds we can run only few prime mover sets to supply all the propellers. Low speed cruising is now no longer uneconomical. 3) position of prime mover Speed control and reversing in case of electric propulsion are easy and can be carried out from any convenient position instead of signaling to engine room
  • 19. • Position is not fixed by the propeller shaft as such there is greater flexibility in the layout.
  • 20. • In Case of very big ships, electric drive will be by three phase induction or synchronous motors • prime mover will be steam turbine, driving three phase alternator. • Speed control is done by variation of applied voltage and partly by frequency variation. • Reversal is obtained by changing the phase sequence of the supply. • Speed of induction motor can also be change by pole changing method which give economical speed. •Disadvantage of induction motor is that it’s P.F. at low speed is low between 0.7 to 0.75. • Power at the ship is generated by turbo alternator at 2.2 to 6.6 kv
  • 21. • Small ships can be driven by D.C. motors, which are controlled by means of ward Leonard method. • Power on the ships is generated by diesel electric set, relatively at low voltage of 650 V
  • 22. TEXTILE MILLS • Loom motors operate in atmosphere which is laden wool-lint and moisture. • Further the motor should high starting torque of about 2to3 times full load torque. • Loom motors have to start and stop many times in a day. • this increases the motor heating during starting. • Motors of low temperature rise under full load conditions are therefore selected do that under working conditions of frequent starting and stopping permissible temperature rise is not exceeded • Keeping above requirements in view totally enclosed, fan cooled, high torque squirrel cage motors are selected
  • 23. • Where only wool lint is present and no moist atmosphere ,screen protected motors are used. • Splash proof motors are used in wet locations such as dye house. • Brush shaft adjustable speed motor is used on printing machine
  • 24. MINES Motor used inside mines should have flame proof enclosure. For mine winders, it is essential to have both speed control as well as breaking capacity Ward Leonard system is most effective drive. Slip Induction motor with D.C. dynamic breaking is also used. We may also used D.C. motor supplied from controlled rectifier.
  • 25. PUNCHES PRESSES & SHEARS • Since heavy sudden loads are applied , D.C. compound motor or slip ring motor with flywheel is used.
  • 26. LATHE, GRINDING & MILLING MACHINE • These machine tools require low starting torque and constant operating speed. • Therefore D.C. shunt motors or squirrel cage motors are needed. • In case of drills, requiring different operating speeds for different metals. • motors having two sets of stator pole changing winding are used which give economical speed.
  • 28. • Drip proof or totally enclosed surface cooled motors are most frequently used, often mounted on a common bed plate and direct coupled to the pump. • Sometimes motor is flange mounted. • Where pump speed does not come within the range of the fixed motor speed ,V belt drive is employed. • starting torque necessary for centrifugal pumps is about 40 to 50% of full load torque. PUMPS
  • 29. • For reciprocating pumps starting torque may be 100 to 200 % of full load torque • It is advisable to use slip ring motors for reciprocating pumps and squirrel cage motors for centrifugal pumps Centrifugal Pump
  • 31. REFRIGERATION & AIR CONDITIONING • In vapor compression system of refrigeration motor is used to drive the compressor. • This motor is controlled by thermostat . • When motor is restarted , it has to drive compressor against high speed pressure. • Motor should therefore be required developing starting torque of 200 to 250% full load torque. • For small unit air conditioners, capacitor type single phase 230 V motor with D.O.L. starter is most commonly selected. • High torque squirrel cage induction motor or slip ring induction motors are used for large installations
  • 32. • For very large plant size, synchronous motor, driving turbo compressor may be found suitable specially when P.F. correction is also required. Compressor
  • 34. LIFTS • High smooth accelerating torque of 200 to 250% full load torque at starting, high over load capacity and pull out torque an maximum degree of silence are essential requirements. • Motor are normally one hour rated for duty cycle of 150 to 180 starts per hour. • D.C. compound motors or slip ring motors suit the above requirements
  • 35. BELT CONVEYERS • Belt conveyors are used for moving sand, coal and others raw materials. • Heavy loads have to accelerated. • High torque squirrel cage or preferably slip ring motors should be made as per requirement. • Due to outside working conditions and presence of grit and dust in atmosphere ,totally enclosed surface cooled motors are used.
  • 37. DOMESTIC USE • Universal series motor is used for house hold appliances such as Mixer, Washing Machine, Sewing Machine, Vacuum Cleaner Mixer
  • 38. Washing Machine Washing Machine Motor Sewing Machine Vacuum Cleaner