Salient Features of India constitution especially power and functions
GovEnergy: The Energy-Water Nexus
1. The Energy-Water Nexus and its Impact on Meeting E.O. 13514 Goals Diana Pape, ICF International August 9, 2011
2. Linkage Between Water and Energy Potential Energy Savings and GHG Savings Associated with Water Efficiency Initiatives Energy Intensity of Water Supply and Wastewater Treatment Potential Energy Savings and GHG Reductions Associated with Water Efficiency Initiatives Current Executive Agency Water Efficiency Initiatives Illustrative Example of Energy Savings by Replacing Appliances Agenda 2
4. 4 DOE End-Use Water Distribution Water Supply & Conveyance Wastewater Collection Wastewater Discharge Wastewater Treatment Water Source
5. Gleick 1993 Consumptive Water Use(Gallons per Thousands of kWh) 5 Energy Supply Requires Water
6. Water Supply and Treatment Requires Energy California Energy Commission 2005 California’s Total Range 2,000 - 20,000 kWh/MG 700 - 1,200 100 - 16,000 0 - 14,000 700 - 1,200 1,100 – 4,600 0 – 400 All Values in kWh/MG 6
7. 7 RiverNetworks 2009 13% Of Nation’s electricity consumption is used for Treatment Distribution Heating Collection Wastewater Treatment Discharge
8. 8 Potential Energy Savings and GHG Savings Associated with Water Efficiency Initiatives
9. ENERGY STAR Products 9 ENERGY STAR 2011 Annual Savings per ENERGY STAR Appliance in an Office Environment Assumes one cycle per day for residential dishwashers. Assumes commercial dishwashers clean two racks per day. A Federal office is open for 260 days a year. Energy and GHG savings come from water pumping, treatment, heating, and wastewater management.
10. WaterSense℠ Products 10 WaterSense 2011 Annual Savings per WaterSense℠ Appliance in an Office Environment Assumes 50 flushes per day, per toilet and urinal in an office environment. A faucet is used for 12.5 minutes per day. Showers run for 50 minutes per day. *Spray valves values come from assumptions from a Notice of Intent and are based upon 50 dishes a day. Energy and GHG savings come from water pumping, treatment, heating, and wastewater management.
11. WaterSense℠ Toilets 11 WaterSense 2011 Replacing a single traditional toilet with a WaterSense℠ (1.28 GPF) toilet would save 25,500 gallons per year = Enough water to fill 3 swimming pools
12. Annual Greenhouse Gas Savings By Scope Annual GHG Emissions Savings per Appliance Assuming wastewater is treated off-site ENERGY STAR 2011, WaterSense 2011 12
17. Energy Intensity Varies by System Type and Size Burton 1996 Energy by Plant Type Energy by Plant Size kWh/Million Gallons (MG) kWh/Million Gallons (MG) 17
18. California Energy Commission 2006 Energy Intensity Varies by Region Northern California Southern California 5,411 kWh/MG 13,021 kWh/MG 18
19. Household Energy Consumption Dishwasher TVs & Computers Roughly 20% of energy used in homes is directly related to water consumption Lighting Clothes Dryer Freezer Refrigerator Water Heating Central Air Conditioning Space Heating California Energy Commission 2006 19
20. 20 Potential Energy Savings and GHG Reductions Associated with Water Efficiency Initiatives
21. Residential Water Saving Strategies Water Use (Gallons per Capita per Day) 38% Potential Savings 69 Water use compared to an average home 53 43 Meyer et al.1999, Aquacraft 2003, ENERGY STAR calculators, WaterSense specifications, and EPAct Standards 21
22. Residential Hot Water Energy Consumption Energy for Heating Water (kWh per Capita per Year) 27% Potential Savings 1,215 Energy use compared to an average home 1,003 893 Aquacraft 2003 22
23. California Energy Commission 2006 Residential Embedded Energy for Water Supply U.S. Average Southern California kWh/Person/Year kWh/Person/Year 286 220 176 37 28 21 Water Supply: 1,785 kWh/MG Water Supply: 11,110 kWh/MG 23
24. California Energy Commission 2006 Potential Embedded Energy Savings in Nine C&I Sectors in California U.S. Average Southern California Million kWh/Day Million kWh/Day 10.1 6.2 1.8 1.1 Water Supply: 1,785 kWh/MG Water Supply: 11,110 kWh/MG 24
26. Number of Agencies that included this strategy as a way to reduce potable water intensity Current Executive Agency Water Efficiency Initiatives Office of Management and Budget 2011 26
27. Agency Water Reduction Accomplishments FY2010 Office of Management and Budget 2011 Federal Reduction in Potable Water Intensity from 2007 Baseline 27
30. FEMP 30 Potential Energy Savings By Replacing Appliances In a 1,000-Person Building
31. U.S. Energy Information Administration 2004 FEMP 31 Equivalent Number of Homes Removed from the Grid
32. Energy and Water are Linked Energy Intensity is Site Specific Opportunities Exist to Leverage Water and Energy Efficiency Initiatives to Save Both Resources Energy Savings are a Significant Co-benefit of Water Efficiency Initiatives Water Efficiency Initiatives Are Strategy to Contribute to Meeting Scope 1 and 2 GHG Goals Conclusions 32
33. References Alliance for Water Efficiency, 2009. AWE Legislative Watch. (http://www.allianceforwaterefficiency.org/Legislative-Watch.aspx#H.R._631) Analysis of Data in Gleick, et al. (2003), Appendix E. Waste Not, Want Not: The Potential for Urban Water Conservation in California. Peter H. Gleick, Dana Haasz, Christine Henges-Jeck, VeenaSrinivasan, Gary Wolff, Katherine Kao Cushing, and Amardip Mann, Pacific Institute for Studies in Development, Environment and Security, Oakland, California, November 2003. Aquacraft, 1999. Residential End Uses of Water, P.W. Mayer, W.B. DeOreo, E.M. Optiz, J.C. Keifer, W.Y. Davis, B. Dziegielewski, and J.O. Nelson, prepared for the American Water Works Association (AWWA) Research Foundation, Denver, Colorado, 1999. Aquacraft, 2003. Residential Indoor Water Conservation Study: Evaluation of High Efficiency Indoor Plumbing Fixture Retrofits in Single-Family Homes in the East Bay Municipal Utility District Service Territory. Prepared for the East Bay Municipal Utility District and the U.S. Environmental Protection Agency by Aquacraft, Inc., Boulder, Colorado, July 2003. AwwaRF, 2008. Risks and Benefits of Energy Management for Drinking Water Utilities. Burton, 1996. Water and Wastewater Industries: Characteristics and Energy Management Opportunities. Franklin L. Burton, Burton Environmental Engineering, Los Altos, CA. Prepared for the Electric Power Research Institute, Palo Alto, California, September 1996, Report CR-106941. CDH Energy Corp, 2007. Energy Index Development for Benchmarking Water and Wastewater Utilities. Prepared for Awwa Research Foundation, 2007. (http://www.nyserda.org/programs/Environment/07-08%20Final%20Report.pdf). CEC, 2005. California’s Water-Energy Relationship. Prepared in response to the 2005 Integrated Energy Policy Report Proceeding (04-IEPR-01E), November 2005. (http://www.energy.ca.gov/2005publications/CEC-700-2005-011/CEC-700-2005-011-SF.PDF). CEC, 2006. Refining Estimates of Water-Related Energy Use in California. Department of Energy, 2006. Energy Demands on Water Resources: Report to Congress on the Interdependency of Energy and Water. (http://www.sandia.gov/energy-water/docs/121-RptToCongress-EWwEIAcomments-FINAL.pdf). EIA, 2011. (http://www.eia.gov/consumption/residential/reports/2009overview.cfm). ENERGY STAR, 2008. Clothes washer and dishwasher savings calculators. ENERGY STAR, 2011. Accessed July 2011. (http://www.energystar.gov/index.cfm?c=products.pr_find_es_products) EPA, 2009. EPA WaterSense 2008 Accomplishments. (http://epa.gov/watersense/docs/ws-accomplishments08_508.pdf). Gleick, 1993. Water in Crisis: A Guide to the World’s Fresh Water Resources. Hill, R. and TamimYunos, 2007. The intertwined tale of energy and water. Virginia Water Resources Research Center. (http://www.vwrrc.vt.edu/watercooler_apr08.html) ICF International, 2008. Water and Energy: Leveraging Voluntary Programs to Save Both Water and Energy. Prepared for U.S. EPA Climate Protection Partnerships Division and Municipal Support Division. March, 2008. (http://www.energystar.gov/ia/partners/publications/pubdocs/Final%20Report%20Mar%202008.pdf). RiverNetwoek, 2009. The Carbon Footprint of Water. WaterSense, 2011. Accessed July 2011. (http://www.epa.gov/WaterSense/products/index.html). U.S. Energy Information Administration. End-Use Consumption of Electricity 2001. (http://www.eia.gov/emeu/recs/recs2001/enduse2001/enduse2001.html) . 2004. 33
35. Thank You! Diana Pape Vice President, Climate Change & Sustainability Division ICF International dpape@icfi.com 202.862.1123 Los Angeles, CA • San Francisco, CA • Denver, CO • Washington, DC • Boston, MA Research Triangle Park, NC • New York City, NY • Dallas, TX • Houston, TX • Seattle, WA 35
Editor's Notes
Assumes 260 working days for a Federal office
NOTE: Potential WaterSense savings are shown from traditional fixtures, not their specifications!General Assumptions230 work days per employee with holidays (of a 260 work day year)Scope 2 is HeatingScope 3 is Water Transport and CleaningToilets (WaterSense)Traditional: 3.5 GPFWaterSense: 1.28 GPF50 Flushes per dayUrinals (WaterSense)Traditional: 1.0 GPFWaterSense: 0.5 GPF50 Flushes per dayFaucets (WaterSense)Traditional: 2.2 GPMWaterSense: 1.6 GPM10 minutes per day of usageShowers (WaterSense)Traditional: 2.5 GPMWaterSense: 2 GPM50 minutes of showers: 5 Minutes per Shower, 10 Showers per Day in an office per showerSpray Valves (WaterSense)Traditional: 1.6 GPMWaterSense: 0.5 GPM (Not listed but quote below shows up to 1.1 GPM less and 1.6-1.1=0.5)50 dishes washed for 26 seconds (FEMP guidance)“Based on current advertised product flow rates, these new valves can use between 0.35 and 1.1 gpm less than standard models” –WaterSense Notice of Intent on commercial spray valves
General Assumptions230 work daysScope 2 is HeatingScope 3 is Water Transport and CleaningToilets (WaterSense)Traditional: 3.5 GPFWaterSense: 1.28 GPF50 Flushes per dayUrinals (WaterSense)Traditional: 1.0 GPFWaterSense: 0.5 GPF50 Flushes per dayFaucets (WaterSense)Traditional: 2.2 GPMWaterSense: 1.6 GPM10 minutes per day of usageShowers (WaterSense)Traditional: 2.5 GPMWaterSense: 2 GPM50 minutes of showers: 5 Minutes per Shower, 10 Showers per Day in an office per shower
Data is from multiple sources including Meyer et al., 1999; Aquacraft, 2003, ENERGY STAR calculators, Water Sense specifications, and EPAct standards. The assumptions for the percent of total water that is hot water is as follows:CW=15% Shower = 72% Faucet = 65% Bath = 90% DW = 100%Cannot see Bath because of the following reason: Bath water consumption is 1.2 gpcd for all scenarios. 90% of bath water use is hot water, therefore, hard to see component that is cold water (only 0.1 gpcd).EPAct Standards for Toilets, Showerheads, and FaucetsToilet--1.6 gallons per flush (gpf). The maximum water use allowed is 1.6 gallons per flush (gpf) for gravity tanktype toilets, flushometer tank toilets, and electromechanical hydraulic toilets, if manufactured after January 1, 1994.Showerhead--2.5 gallons per minute (gpm) at 80 psi. The maximum water use allowed for any showerheads manufactured after January 1, 1994, shall be 2.5 gallons per minute (9.5 liters per minute) when measured at a flowing pressure of 80 pounds per square inch gage (552 kilopascals). Any such showerhead shall also meet the requirements of ASME/ANSI Standard A112.18.1M–1996, 7.4.4(a).Faucet -2.2 gallons per minute (gpm) at 60 psi. The maximum water use allowed for any of the following faucets manufactured after January 1, 1994, when measured at a flowing water pressure of 60 pounds per square inch (414 kilopascals), shall be as follows: Lavatory faucets: 2.2 gpm (8.3 L/min); Lavatory replacement aerators: 2.2 gpm (8.3 L/min); Kitchen faucets: 2.2 gpm (8.3 L/min); Kitchen replacement aerators: 2.2 gpm (8.3 L/min); Metering faucets: 0.25 gal/cycle (0.95 L/cycle)Water Sense 1.28 gpf Faucets – 1.5 gpmCW WF = 8.0
The following assumptions were used to estimate hot water heating energy consumption:1. Percent of total water that is hot water for Clothes washers is 15%, for showers is 72%, for faucets is 65%, for baths is 90%, and for dishwashers is 100%. (source: Aquacraft, 2003) Water heater outlet temperature = 120 F (source: RESNET's 2006 Mortgage Industry National Home Energy Rating Standards, Page 3-15) Water heater inlet temperature = 58 F (source: ANSI/ASHRAE 118.2-1993, Appendix A) Energy Factor (i.e., minimum federal efficiency for new 40 gallon electric tank) = 0.917 (Federal Register, Part VIII, DOE, 10 CFR Part 430, page 4497) Recovery efficiency (i.e., combustion efficiency) = 1.00 (by definition for electric water heaters) Room air temperature = 70 F (ANSI/ASHRAE 118.2-1993, Appendix A)NOTE: These energy estimates (and all hot water energy estimates in this presentation) assume an electric hot water heater.
President Obama signs Executive Order 13514 while many cabinet members stand behind. E.O. 13514 expands energy reduction goals of the executive agency and makes reducing GHGs a priority for the Federal government. Photo courtesy of the White House.
General Assumptions230 work days per person, 260 operating days per officeScope 2 is HeatingScope 3 is Water Transport and CleaningToilets (WaterSense)Traditional: 3.5 GPFWaterSense: 1.28 GPF50 Flushes per dayUrinals (WaterSense)Traditional: 1.0 GPFWaterSense: 0.5 GPF50 Flushes per dayFaucets (WaterSense)Traditional: 2.2 GPMWaterSense: 1.6 GPM10 minutes per day of usageShowers (WaterSense)Traditional: 2.5 GPMWaterSense: 2 GPM50 minutes of showers: 5 Minutes per Shower, 10 Showers per Day in an office per shower