Dev Dives: Streamline document processing with UiPath Studio Web
Alcatel lucent pt telkom turn-up guide v1
1. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 1 of 27
PT Telkom Vectoring Field Trial
Method of Procedure
Alcatel-Lucent 7356REM ISAM Turn Up Guide
Author: Fiona Tay
Document: Turn-up Guide
Version: 0.1
Status: Draft
Last Revised: June 24, 2014
2. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 2 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
TABLE OF CONTENTS
1 PREFACE.................................................................................................................. 5
2 COMPATIBILITY ..................................................................................................... 5
3 CONVENTIONS ........................................................................................................ 5
4 PRE-CONFIGURA TION STEPS ................................................................................ 6
4.1 CONNECT TO THE 7360FX OLT & 7356REM MDU ISAM VIA CRAFT TERMINAL...........................6
5 OLT BASIC SETUP - INITIA L CONFIGURA TION.................................................... 8
5.1 RESET THE SYSTEM WITH CLEAN DATABASE............................................................................................8
5.2 CONFIGURE UPLINK PORTS........................................................................................................................8
5.3 CONFIGURE MANAGEMENT VLAN.............................................................................................................8
5.4 CONFIGURE SYSTEM IP ADDRESS ............................................................................................................8
5.5 CONFIGURE SYSTEM ID............................................................................................................................9
5.6 CONFIGURE SYSTEM PROMPT...................................................................................................................9
5.7 CONFIGURE SYSTEM LOGIN BANNER.........................................................................................................9
5.8 CONFIGURE SLOT BANDWIDTH ................................................................................................................9
5.9 CONFIGURE SLOT NUMBERING & DHCP OPTION82 FORMAT..............................................................9
5.10 DISABLE PASSWORD AGING & TIMEOUT FOR OPERATOR LOGIN........................................................9
5.11 CONFIGURE THE SNMP COMMUNITIES ............................................................................................ 10
5.12 SAVE THE CONFIGURATION............................................................................................................... 10
5.13 CONFIGURE SNTP............................................................................................................................. 10
5.14 PLAN ALL INSERTED CARDS ............................................................................................................... 10
5.15 ENABLE PON PORTS ......................................................................................................................... 10
5.16 REBOOT 7360FX OLT...................................................................................................................... 11
6 MDU BASIC SETUP - INITIAL CONFIGURA TION ................................................ 12
6.1 RESET THE SYSTEM WITH CLEAN DATABASE......................................................................................... 12
6.2 CONFIGURE UPLINK PORTS..................................................................................................................... 12
6.3 CONFIGURE MANAGEMENT VLAN.......................................................................................................... 12
6.4 CONFIGURE SYSTEM IP ADDRESS ......................................................................................................... 12
6.5 CONFIGURE SYSTEM ID......................................................................................................................... 12
6.6 CONFIGURE SYSTEM PROMPT................................................................................................................ 13
6.7 CONFIGURE SYSTEM LOGIN BANNER...................................................................................................... 13
6.8 CONFIGURE SLOT BANDWIDTH ............................................................................................................. 13
6.9 CONFIGURE SLOT NUMBERING & DHCP OPTION82 FORMAT........................................................... 13
6.10 DISABLE PASSWORD AGING & TIMEOUT FOR OPERATOR LOGIN..................................................... 13
3. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 3 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
6.11 CONFIGURE THE SNMP COMMUNITIES ............................................................................................ 14
6.12 SAVE THE CONFIGURATION............................................................................................................... 14
6.13 CONFIGURE SNTP............................................................................................................................. 14
6.14 PLAN ALL INSERTED CARDS ............................................................................................................... 14
6.15 REBOOT ISAM ................................................................................................................................... 14
7 OLT SERVICE PROVISIONING - INITIAL CONFIGURA TION.............................. 15
7.1 CREATE UPSTREAM BANDWIDTH PROFILES (DBA)............................................................................. 15
7.2 CREATE DOWNSTREAM SHAPER PROFILES........................................................................................... 15
7.3 CREATE PBIT TO TC MAPPING PROFILES............................................................................................. 15
7.4 CONFIGURE SYSTEM MULTICAST FOR IPTV ........................................................................................ 15
7.5 CREATE VLANS ...................................................................................................................................... 16
8 MDU SERVICE PROVISIONING - INITIA L CONFIGURA TION ............................ 18
8.1 CREATE VECTORING CONTROL ENTITY (VCE) PROFILE AND ASSOCIATE IT TO A BOARD ............... 18
8.2 CREATE XDSL VECTORING PROFILES................................................................................................... 18
8.3 CREATE XDSL SERVICE PROFILES ........................................................................................................ 18
8.4 CREATE XDSL SPECTRUM PROFILES..................................................................................................... 18
8.5 CREATE XDSL RTX PROFILES................................................................................................................ 21
8.6 CONFIGURE SYSTEM MULTICAST FOR IPTV ........................................................................................ 21
8.7 CREATE VLANS ...................................................................................................................................... 22
8.8 CREATE VOIP SERVICE.......................................................................................................................... 22
9 SERVICE PROVISIONING – SAMPLE SERVICE CONFIGURA TION..................... 24
9.1 CREATE SFP ONT INFRASTRUCTURE................................................................................................... 24
9.2 CONFIGURE SFP ONT UNI................................................................................................................... 24
9.3 CREATE HSI SERVICE ON SFP ONT .................................................................................................... 24
9.4 CREATE VOD + MULTICAST SERVICE ON SFP ONT.......................................................................... 24
9.5 CREATE VOIP SERVICE ON SFP ONT .................................................................................................. 24
9.6 CREATE XDSL VECTORED LINE ............................................................................................................. 25
9.7 CREATE HSI SERVICE (RGW) .............................................................................................................. 25
9.8 CREATE VOD + MULTICAST SERVICE.................................................................................................. 25
9.9 CREATE VOIP SERVICE.......................................................................................................................... 25
10 USEFUL SHOW COMMA NDS .............................................................................. 25
10.1 VIEW VECTOR DISTURBERS ON VDSL2 VECTORING LINES............................................................. 25
10.2 VIEW THE XDSL LINE STATUS .......................................................................................................... 25
10.3 SHOW IGMP STATISTICS ................................................................................................................. 26
10.4 SHOW SIP STATISTICS..................................................................................................................... 26
4. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 4 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
10.5 MIRROR ON OLT ............................................................................................................................... 26
10.6 MIRROR ON MDU.............................................................................................................................. 26
11 DOCUMENT HISTORY........................................................................................ 27
5. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 5 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
1 Preface
This document describes the process of configuring a 7356REM ISAM for use in PT
Telkom network for the Vectoring Field Trial.
2 Compatibility
This document supports the configuration of the 7356REM ISAM with the following
release:
ISAM R5.0 or higher
3 Conventions
The following conventions are used throughout this document:
Courier New font: denotes to be entered commands, and their output.
The # prompt denotes login as root;
The > prompt denotes login as normal user.
Bold italics Arial font: denotes GUI actions (menu selections or buttons).
6. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 6 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
4 Pre-configuration steps
4.1 Connect to the 7360FX OLT & 7356REM MDU ISAM via Craft Terminal
Connect the PC’s Serial port to the craft port of the 7356REM ISAM (LCMI). The craft
port is located on the NRNT-A card.
Pin-out of RJ45 connector:
Signal Description Pin Type
RI_DSR Data-Set-Ready 1 O
DCD Data-Carrier-Detect 2 O
DTR Data-Terminal-Ready 3 I
EG Signal Ground 4 Ref
RXD Receive-Data 5 O
TXD Transmit-Data 6 I
CTS Clear-To-Send 7 O
RTS Request-To-Send 8 I
Open HyperTerminal (or equivalent) and setup the serial connection with following
parameters:
As soon as you connect the system will show following prompt:
Would you like a CLI(C) or a TL1 login(T) or TL1 normal session(N) ? [N]:
Choose ‘C’ to enter the TL1. The factory username and password are:
Username = isadmin
Password = i$@mad-
7. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 7 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
This password needs to be changed on first logon. Please change it to “ans#150”
(without the quotes)
8. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 8 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
5 OLT Basic Setup - Initial configuration
5.1 Reset the system with clean database
Remove any existing configuration.
isadmin># admin software-mngt oswp 1 activate clear-db
Note: The system will reset and come up with an empty database. Follow step 4.1 to
re-connect to the system.
5.2 Configure uplink ports
Configure 1 uplink to connect to the network, port 1 on NT in 1GE mode for connection
to Metro-E.
isadmin># configure port nt-a:xfp:1 ethernet speed 1000
isadmin># configure port nt-a:xfp:1 ethernet autonegotiate
limited
isadmin># configure port nt-a:xfp:1 no shutdown
Note: The ports have a MTU of 2000 Bytes configured by default
5.3 Configure management VLAN
Assign the management VLAN to Uplink.
isadmin># configure service vpls 82 customer 1 v-vpls vlan 82
create
isadmin># configure service vpls 82 description "management
vlan"
isadmin># configure service vpls 82 nt-a:xfp:1:82 create
isadmin># configure service vpls 82 no shutdown
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
5.4 Configure System IP address
Assign the management IP address and routing table.
isadmin># configure system management host-ip-address
manual:172.27.141.56/26
isadmin># configure system management default-route 172.27.141.1
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: System is now reachable from EMS and the network.
9. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 9 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
5.5 Configure System ID
Configure the system name.
isadmin># configure system id 09-TDS-01;
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
5.6 Configure System Prompt
Configure the system prompt to represent the system name and use type based LT
numbering.
isadmin># configure system security operator isadmin prompt
"%s:%n@AR09-TDS-01%d%c"
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The total length of the prompt string needs to be less or equal than 28
characters. This means the system ID can only be 18 characters.
5.7 Configure system login banner
Configure the system CLI login banner
isadmin># configure system security login-banner "Access to the
ISAM system is for authorized staff only"
isadmin># configure system security welcome-banner "Alcatel-
Lucent 7360FX OLT"
5.8 Configure Slot Bandwidth
Configure the system slot bandwidth between the switching matrix and the Line cards
(value is speed between line card and each controller)
isadmin># configure system max-lt-link-speed link-speed forty-gb
5.9 Configure Slot Numbering & DHCP Option82 Format
Configure the slot numbering format and the DHCP Option82 format
isadmin># configure system security profile admin slot-numbering
type-based
isadmin># configure system port-num-in-proto type-based
isadmin># configure system loop-id-syntax efm-based-pon
"Access_Node_ID eth Rack/Frame/Slot/Port/ONU/OnuSlt/UNI"
Note: After setting this slot numbering the operator needs to logout and login again to
activate the new setting
5.10 Disable password aging & timeout for operator login
Disable the password aging and session time out for operator login
10. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 10 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
isadmin># configure system security profile admin password-
timeout 0
isadmin># configure system security ssh server-profile idle-
timeout 300
5.11 Configure the SNMP communities
To allow 5520AMS access, the host-address used is the IP address of the AMS,
optionally this can be set to a subnet or 0.0.0.0/0 to allow access to all hosts.
isadmin># configure system security snmp community public host-
address 10.153.5.65/32 context nt
isadmin># configure system security snmp community NETMAN host-
address 10.153.5.65/32 context shub
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
5.12 Save the configuration
isadmin># admin software-mngt ihub database save-protected
5.13 Configure SNTP
Configure SNTP server for network time synchronization.
isadmin># configure system sntp server-ip-addr 10.153.5.65
timezone-offset 420 enable
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The NTP server IP points to the AMS Server
5.14 Plan all inserted cards
Configure all cards in the system
isadmin># configure equipment slot nt-a planned-type fant-f
unlock
isadmin># configure equipment slot lt:1/1/1 planned-type nglt-c
unlock
5.15 Enable PON Ports
Enable PON in the system.
isadmin># configure pon interface 1/1/1/1 admin-state up
isadmin># configure qos interface pon:1/1/1/1 ds-num-queue 8
12. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 12 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
6 MDU Basic Setup - Initial configuration
6.1 Reset the system with clean database
Remove any existing configuration.
isadmin># admin software-mngt oswp 1 activate clear-db
Note: The system will reset and come up with an empty database. Follow step 4.1 to
re-connect to the system.
6.2 Configure uplink ports
Configure 1 uplink to connect to the network, port 1 on NT in 1GE mode for connection
to OLT.
isadmin># configure interface shub port nt:sfp:1 port-type
network mode 1gbps:full admin-status up
Note: The ports have a MTU of 2000 Bytes configured by default
6.3 Configure management VLAN
Assign the management VLAN to Link Aggregation Group.
isadmin># configure system mgnt-vlan-id 82
isadmin># configure system shub entry vlan ext-vlan-id 82
isadmin># configure vlan shub id 82 egress-port nt:sfp:1
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
6.4 Configure System IP address
Assign the management IP address and routing table.
isadmin># configure system management host-ip-address
manual:127.72.141.57/26
isadmin># configure system management default-route 172.27.141.1
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: System is now reachable from EMS and OLT
6.5 Configure System ID
Configure the system name.
isadmin># configure system id 09-TDS-01;
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
13. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 13 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
6.6 Configure System Prompt
Configure the system prompt to represent the system name and use type based LT
numbering.
isadmin># configure system security operator isadmin prompt
"%s:%n@09-TDS-01%d%c"
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The total length of the prompt string needs to be less or equal than 28
characters. This means the system ID can only be 18 characters.
6.7 Configure system login banner
Configure the system CLI login banner
isadmin># configure system security login-banner "Access to the
ISAM system is for authorized staff only"
isadmin># configure system security welcome-banner "Alcatel-
Lucent 7356REM MDU"
6.8 Configure Slot Bandwidth
Configure the system slot bandwidth between the switching matrix and the Line cards
(value is speed between line card and each controller)
isadmin># configure system max-lt-link-speed link-speed
twodotfive-gb
6.9 Configure Slot Numbering & DHCP Option82 Format
Configure the slot numbering format and the DHCP Option82 format
isadmin># configure system security profile admin slot-numbering
type-based
isadmin># configure system port-num-in-proto type-based
isadmin># configure system loop-id-syntax efm-based-dsl
"Access_Node_ID eth Rack/Frame/Slot/Port"
Note: After setting this slot numbering the operator needs to logout and login again to
activate the new setting
6.10 Disable password aging & timeout for operator login
Disable the password aging and session time out for operator login
isadmin># configure system security profile admin password-
timeout 0
isadmin># configure system security ssh server-profile idle-
timeout 300
14. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 14 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
6.11 Configure the SNMP communities
To allow 5520AMS access , the host-address used is the IP address of the AMS,
optionally this can be set to a subnet or 0.0.0.0/0 to allow access to all hosts.
isadmin># configure system security snmp community public host-
address 10.153.5.65/32 context nt
isadmin># configure system security snmp community NETMAN host-
address 10.153.5.65/32 context shub
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
6.12 Save the configuration
isadmin># admin software-mngt shub database save
6.13 Configure SNTP
Configure SNTP server for network time synchronization.
isadmin># configure system sntp server-ip-addr 10.153.5.65
timezone-offset 420 enable
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The NTP server IP points to the AMS Server
6.14 Plan all inserted cards
Configure all cards in the system
isadmin># configure equipment slot nt-a planned-type nrnt-a
unlock
isadmin># configure equipment slot lt:1/1/1 planned-type ndlt-c
unlock
isadmin># configure equipment slot lt:1/1/2 planned-type npot-c
unlock
6.15 Reboot ISAM
Reboot the 7356REM MDU
isadmin># admin equipment reboot-isam without-self-test
15. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 15 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
7 OLT Service Provisioning - Initial configuration
7.1 Create Upstream Bandwidth Profiles (DBA)
Create Bandwidth profiles according to the type of service. These profiles regulate the
DBA bandwidth and priority.
isadmin># configure qos profiles bandwidth UP_1G committed-info-
rate 0 assured-info-rate 10000 excessive-info-rate 1000000
delay-tolerance 8
7.2 Create Downstream Shaper Profiles
Create Bandwidth profiles according to the type of service. These profiles are used for
rate shaping on Line card
isadmin># configure qos profiles shaper DN_1G committed-info-
rate 0 committed-burst-size 0 excess-info-rate 1000000 type
singletokenbucketgpon
7.3 Create Pbit to TC Mapping Profiles
Create PBit to Traffic Class mapping profiles.
isadmin># configure qos profiles ingress-qos Default_TC0 dot1-
p0-tc 0 dot1-p1-tc 0 dot1-p2-tc 0 dot1-p3-tc 0 dot1-p4-tc 0
dot1-p5-tc 0 dot1-p6-tc 0 dot1-p7-tc 0
isadmin># configure qos profiles ingress-qos Ingress_Default
dot1-p0-tc 0 dot1-p1-tc 1 dot1-p2-tc 2 dot1-p3-tc 3 dot1-p4-tc 4
dot1-p5-tc 5 dot1-p6-tc 6 dot1-p7-tc 7
7.4 Configure System Multicast for IPTV
Enable Multicast on System Level:
isadmin># configure igmp system src-ip-address 10.88.43.222
query-interval 125 start user-igmp-version 2 netw-igmp-version 2
Create Multicast VLAN:
isadmin># configure vlan id 110 mode residential-bridge name
IPTV new-broadcast enable in-qos-prof-name name:Default_TC0
isadmin># configure port nt-a:xfp:1 ethernet autonegotiate
limited
isadmin># configure port nt-a:xfp:1 ethernet speed 1000
isadmin># configure port nt-a:xfp:1 no shutdown
isadmin># configure service vpls 110 customer 1 v-vpls vlan 110
create
isadmin># configure service vpls 110 description "IPTV"
isadmin># configure service vpls 110 sap nt-a:xfp:1:110 create
16. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 16 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
isadmin># configure service vpls 110 sap nt-a:xfp:1:110 igmp-
snooping mrouter-port
isadmin># configure service vpls 110 sap lt:1/1/1:110 create
isadmin># configure service vpls 110 sap lt:1/1/1:110 igmp-
snooping version 2
isadmin># configure service vpls 110 sap lt:1/1/1:110 igmp-
snooping send-queries
isadmin># configure service vpls 110 igmp-snooping no shutdown
isadmin># configure service vpls 110 no shutdown
Create Multicast Channels:
isadmin># configure mcast chn 239.200.10.[1...10] src-ip-addr
0.0.0.0 vlan-id 20 guaranteed-serv peak-bit-rate 8000
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
7.5 Create VLANs
Create VLANs on system and assign to all LTs and Uplink
HSI VLAN:
isadmin># configure vlan id 3210 mode residential-bridge name
HSI new-broadcast enable
isadmin># configure vlan id stacked:1284:10 mode residential-
bridge name HSI in-qos-prof-name name: Ingress_Default
isadmin># configure service vpls 3210 customer 1 v-vpls vlan
3210 create
isadmin># configure service vpls 3210 description "HSI"
isadmin># configure service vpls 3210 sap nt-a:xfp:1:3210 create
isadmin># configure service vpls 3210 sap lt:1/1/1:3210 create
isadmin># configure service vpls 3210 no shutdown
VoIP (SIP) VLAN:
isadmin># configure vlan id 2929 mode residential-bridge name
SIP in-qos-prof-name name: Ingress_Default
isadmin># configure service vpls 2929 customer 1 v-vpls vlan
2898 create
isadmin># configure service vpls 2929 description "SIP"
isadmin># configure service vpls 2929 sap nt-a:xfp:1:2929 create
isadmin># configure service vpls 2929 sap lt:1/1/1:2929 create
isadmin># configure service vpls 2929 no shutdown
VoD VLAN:
17. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 17 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
isadmin># configure vlan id 111 mode residential-bridge name VoD
in-qos-prof-name name: Ingress_Default
isadmin># configure service vpls 111 customer 1 v-vpls vlan 111
create
isadmin># configure service vpls 111 description "VoD"
isadmin># configure service vpls 111 sap nt-a:xfp:1:111 create
isadmin># configure service vpls 111 sap lt:1/1/1:111 create
isadmin># configure service vpls 111 no shutdown
Multicast VLAN:
isadmin># configure vlan id 110 mode residential-bridge name
IPTV in-qos-prof-name name: Ingress_Default
isadmin># configure service vpls 110 customer 1 v-vpls vlan 110
create
isadmin># configure service vpls 110 description "IPTV"
isadmin># configure service vpls 110 sap nt-a:xfp:1:110 create
isadmin># configure service vpls 110 sap lt:1/1/1:110 create
isadmin># configure service vpls 110 no shutdown
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
18. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 18 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
8 MDU Service Provisioning - Initial configuration
8.1 Create Vectoring Control Entity (VCE) Profile and associate it to a board
A non-null Vectoring Control Entity (VCE) profile should be associated to a board which
is capable of processing the vectoring algorithms (Board Level Vectoring (BLV) board).
isadmin># configure xdsl vce-profile 1 name VCE_DEFAULT version
1 vce-join-timeout 20 active
isadmin># configure xdsl board 1/1/1 vce-profile 1
8.2 Create xDSL Vectoring Profiles
isadmin># configure xdsl vect-profile 1 name VECT_US_DS
isadmin>configure>xdsl>vect-profile>1$ version 1
isadmin>configure>xdsl>vect-profile>1$ active
isadmin>configure>xdsl>vect-profile>1$ exit
8.3 Create xDSL Service Profiles
Create xDSL Service Profiles.
isadmin># configure xdsl service-profile 1 name
MaxUS_MaxDS_SRA_FAST
isadmin>configure>xdsl>service-profile>1$ version 1
isadmin>configure>xdsl>service-profile>1$ ra-mode-down dynamic
isadmin>configure>xdsl>service-profile>1$ ra-mode-up dynamic
isadmin>configure>xdsl>service-profile>1$ min-bitrate-down 32
isadmin>configure>xdsl>service-profile>1$ min-bitrate-up 32
isadmin>configure>xdsl>service-profile>1$ plan-bitrate-down 1024
isadmin>configure>xdsl>service-profile>1$ max-bitrate-down
262140
isadmin>configure>xdsl>service-profile>1$ max-bitrate-up 50000
isadmin>configure>xdsl>service-profile>1$ max-delay-down 2
isadmin>configure>xdsl>service-profile>1$ max-delay-up 2
isadmin>configure>xdsl>service-profile>1$ active
isadmin>configure>xdsl>service-profile>1$ exit
8.4 Create xDSL Spectrum Profiles
Create xDSL Spectrum Profiles.
isadmin># configure xdsl spectrum-profile 1 name VDSL2_noUPBO
isadmin>configure>xdsl>spectrum-profile>1$ version 1
isadmin>configure>xdsl>spectrum-profile>1$ dis-ansi-t1413
isadmin>configure>xdsl>spectrum-profile>1$ dis-etsi-dts
21. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 21 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# param-a
5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# param-b
943
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# exit
isadmin>configure>xdsl>spectrum-profile>1# active
isadmin>configure>xdsl>spectrum-profile>1# exit
8.5 Create xDSL Rtx Profiles
Create xDSL Rtx Profiles.
isadmin># configure xdsl rtx-profile 1 name ARQUSDS
isadmin>configure>xdsl>rtx-profile>1$ version 1
isadmin>configure>xdsl>rtx-profile>1$ min-exp-thrpt-dn 2000
isadmin>configure>xdsl>rtx-profile>1$ min-exp-thrpt-up 180
isadmin>configure>xdsl>rtx-profile>1$ plan-exp-thrpt-dn 20000
isadmin>configure>xdsl>rtx-profile>1$ plan-exp-thrpt-up 1024
isadmin>configure>xdsl>rtx-profile>1$ max-exp-thrpt-dn 131000
isadmin>configure>xdsl>rtx-profile>1$ max-exp-thrpt-up 50000
isadmin>configure>xdsl>rtx-profile>1$ max-net-rate-dn 131000
isadmin>configure>xdsl>rtx-profile>1$ max-net-rate-up 50000
isadmin>configure>xdsl>rtx-profile>1$ shine-ratio-dn 0
isadmin>configure>xdsl>rtx-profile>1$ shine-ratio-up 0
isadmin>configure>xdsl>rtx-profile>1$ active
isadmin>configure>xdsl>rtx-profile>1$ exit
8.6 Configure System Multicast for IPTV
Enable Multicast on System Level:
isadmin># configure mcast general fast-change
isadmin># configure mcast general package-member [1...1024]
isadmin># configure igmp system src-ip-address 10.88.43.222
start user-igmp-version 2 netw-igmp-version 2
isadmin># configure igmp shub igs-system start-snooping enable-
snooping self-ip-addr-mode configure
Create Multicast VLAN:
isadmin># configure vlan shub id 110 mode residential-bridge
name IPTV
isadmin># configure vlan shub id 110 egress-port lt:1/1/1
isadmin># configure vlan shub id 110 egress-port nt:sfp:1
isadmin># configure vlan id 110 mode residential-bridge name
IPTV new-broadcast enable
22. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 22 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
Create Multicast Channels:
isadmin># configure qos cac-mode nocac
isadmin># configure mcast channel 239.1.1.[1...254] src-ip-addr
0.0.0.0 peak-bit-rate 1000 vlan-id 110
isadmin># configure mcast channel 239.1.2.[1...254] src-ip-addr
0.0.0.0 peak-bit-rate 1000 vlan-id 110
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
8.7 Create VLANs
Create VLANs on system and assign to all LTs and Uplink
HSI VLAN:
isadmin># configure vlan shub id 3210 mode residential-bridge
name HSI
isadmin># configure vlan shub id 3210 egress-port lt:1/1/1
isadmin># configure vlan shub id 3210 egress-port nt:sfp:1
isadmin># configure vlan id 3210 mode residential-bridge name
HSI broadcast-frames
VoD VLAN:
isadmin># configure vlan shub id 111 mode residential-bridge
name VoD user2-comm disable
isadmin># configure vlan shub id 111 egress-port lt:1/1/1
isadmin># configure vlan shub id 111 egress-port nt:sfp:1
isadmin># configure vlan id 111 mode residential-bridge name VoD
broadcast-frames
Voice VLAN:
isadmin># configure vlan shub id 2929 mode voice-vlan name SIP
isadmin># configure vlan shub id 2929 egress-port lt:1/1/1
isadmin># configure vlan shub id 2929 egress-port nt:sfp:1
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
8.8 Create VOIP Service
Create Voice(SIP) Service for connection to the softswitch.
isadmin># configure voice sip server sip1 address
ipv4:10.0.0.110 admin-domain-name vsp1 admin-status up
23. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 23 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
isadmin># configure voice sip lineid-syn-prof profile1 pots-
syntax random
isadmin># configure voice sip user-agent ua_01 ip-config-mode
dhcp ip-addr-policy distributed signal-vlan-id 2929 rtp-vlan-id
2929 admin-status up
isadmin># configure voice sip transport udp provider-name vsp1
admin-status up
isadmin># configure voice sip register vsp1 register-uri
telkom.net.id
isadmin># configure voice sip vsp vsp1 domain-name 10.0.0.110
isadmin># configure voice sip vsp vsp1 admin-status up
isadmin># configure voice sip user-agent-ap ua_01 slot-id
lt:1/1/2 admin-status up
isadmin># configure voice sip dialplan dp1
isadmin># configure voice sip digitmap dp1 type regular rule x.T
isadmin># configure voice sip redundancy vsp1 bg-monitor-int 0
isadmin># configure voice sip system session-timer admin-status
up
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
24. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 24 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
9 Service Provisioning – Sample Service Configuration
9.1 Create SFP ONT Infrastructure
Create ONTs using SLID Password.
isadmin># configure equipment ont interface 1/1/1/1/1 sw-ver-
pland 3FE55040AOPA21 sernum ALCL: FAB00CAC fec-up enable enable-
aes enable
isadmin># configure equipment ont slot 1/1/1/1/1/1 planned-card-
type 10_100base plndnumdataports 1 plndnumvoiceports 0 port-type
nni admin-state up
isadmin># configure qos interface ont:1/1/1/1/1 us-num-queue 8
isadmin># configure interface port uni:1/1/1/1/1/1/1 no admin-up
isadmin># configure qos interface ont:1/1/1/1/1 scheduler-node
name:NGLT_Default
9.2 Configure SFP ONT UNI
isadmin># configure interface port uni:1/1/1/1/1/1/1 admin-up
isadmin># configure qos interface 1/1/1/1/1/1/1 scheduler-node
name:NGLT_Default
isadmin># configure qos interface 1/1/1/1/1/1/1 cac-profile
name:FD_GponVideo
isadmin># configure qos interface 1/1/1/1/1/1/1 upstream-queue
[0...7] weight 0 bandwidth-profile UP_1G bandwidth-sharing ont-
sharing
isadmin># configure qos interface 1/1/1/1/1/1/1 queue [0…7]
priority 1 weight 1
isadmin># configure bridge port /1/1/1/1/1/1 max-unicast-mac
2048
9.3 Create HSI Service on SFP ONT
Create HSI service on port 1 using HSI VLAN.
isadmin># configure bridge port 1/1/1/1/1/1/1 vlan-id 3210 tag
single-tagged network-vlan 3210 vlan-scope local
9.4 Create VOD + Multicast Service on SFP ONT
Create VOD + Multicast Service using VOD VLAN.
isadmin># configure bridge port 1/1/1/1/1/1/1 vlan-id 111 tag
single-tagged network-vlan 111 vlan-scope local
isadmin># configure igmp channel vlan:1/1/1/1/1/1/1:110 max-num-
group 1024 max-msg-rate 256
9.5 Create VoIP Service on SFP ONT
Create VOIP services
25. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 25 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
isadmin># configure bridge port 1/1/1/1/1/1/1 vlan-id 2929 tag
single-tagged network-vlan 2929 vlan-scope local
9.6 Create xDSL Vectored Line
Create xDSL Vectored Line.
isadmin># configure xdsl line 1/1/1/1 service-profile 1
spectrum-profile 1 rtx-profile 1 vect-profile 1 carrier-data-
mode on transfer-mode ptm admin-up
9.7 Create HSI Service (RGW)
Create HSI service
isadmin># configure bridge port 1/1/1/1 max-unicast-mac 16
isadmin># configure bridge port 1/1/1/1 vlan-id 3210 tag single-
tagged
isadmin># configure bridge port 1/1/1/1 pvid 3210
9.8 Create VOD + Multicast Service
Create VOD +Multicast service
isadmin># configure bridge port 1/1/1/1 max-unicast-mac 16
isadmin># configure bridge port 1/1/1/1 vlan-id 111 tag single-
tagged
isadmin># configure igmp channel vlan:1/1/1/1:110 max-num-group
16
9.9 Create VoIP Service
Create VoIP service
isadmin># configure voice sip termination 1/1/2/1 directory-
number +623151511024 user-name +623151511024@telkom.net.id uri
+623151511024@telkom.net.id md5-realm telkom.net.id md5-password
plain:telkom135 admin-status up
isadmin># configure voice sip termination 1/1/2/2 directory-
number +623151511025 user-name +623151511025@telkom.net.id uri
+623151511025@telkom.net.id md5-realm telkom.net.id md5-password
plain:telkom135 admin-status up
10 Useful Show Commands
10.1 View vector disturbers on VDSL2 vectoring lines
View the actual mapping between the VP board and the SLV LT boards.
isadmin># show xdsl vect-disturbers 1/1/1/1 max-reported-dist 48
10.2 View the xDSL line status
View the xDSL line status.
26. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 26 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
isadmin># show xdsl operational-data line
View the mode of vectoring supported on CPE.
isadmin># show xdsl operational-data near-end line 1/1/1/1
detail
10.3 Show IGMP Statistics
Show IGMP statistics.
isadmin># show igmp channel counter
isadmin># show igmp channel miscellaneous
10.4 Show SIP Statistics
Show SIP statistics.
isadmin># show voice sip server
isadmin># show voice sip user-agent-ap
isadmin># show voice sip termination
10.5 Mirror on OLT
Mirroring on OLT.
isadmin># configure port nt-a:eth:1 ethernet autonegotiate
limited
isadmin># configure port nt-a:eth:1 no shutdown
isadmin># debug mirror-source 1 port nt-a:xfp:1 egress ingress
isadmin># debug mirror-source 1 no shutdown
isadmin># configure mirror mirror-dest 1 sap nt-a:eth:1:0
isadmin># configure mirror mirror-dest 1
isadmin># info configure mirror
isadmin># show debug
10.6 Mirror on MDU
Mirroring on MDU.
isadmin># configure interface shub port nt:eth:1 port-type
network admin-status auto-up
isadmin># configure interface shub mirror enable to-port
nt:sfp:2
isadmin># configure interface shub mirror port nt:sfp:1 external
ingress egress
isadmin># configure interface shub mirror port nt:sfp:1 internal
ingress egress
isadmin># info configure interface shub mirror
27. Method of Procedure- 7356REM ISAM Turn-up Guide - Page 27 of 27
Allrightsreserved.Passingonandcopyingofthisdocument,useand
communicationofitscontentsnotpermittedwithoutwrittenauthorization
fromAlcatel-Lucent.
11 Document History
Version Date Author(s) Description/Comment
0.1 June 24th 2014 Fiona Tay Document Creation
- END OF DOCUMENT -